manualshive.com logo in svg

Solid State Logic Fusion, Руководство пользователя

Поделиться
Скачать
Solid State Logic Fusion Скачать руководство пользователя страница 23

18

 Fusion User Guide

Troubleshooting & FAQ's

Troubleshooting & FAQ's

Frequently Asked Questions can be found on the Solid State Logic Website at: 

http://www.solidstatelogic.com/support/fusion

If you require technical support for Fusion or other SSL Products, click on the Ask a 
Question link on the support page to open a support ticket and an SSL Product Support 
Engineer will be in contact.

UID Display Mode

UID Display Mode displays the UID number of the firmware currently in use and the hardware revision of both main card and front 
panel card. To enter UID Display Mode, switch the unit on and hold down the 

PRE   EQ

 and 

BYPASS

 switches during the startup 

LED sequence.

Unique ID (UID)

The UID is a five digit number. Pressing any of the first five front panel switches allows the selection of any of the five digits of the 
UID. The selected digit will be represented on the right main meter bar (see table below). 

0 LEDs on

current digit is 0

1 LED on 

current digit is 1

2 LEDs on

current digit is 2

...

...

Hardware Revision

To display the hardware revision of the boards, press the 

PRE   EQ

 switch whilst in UID Display Mode (which will light up blue). On 

the left meter, the mainboard revision number is displayed (see table below). On the right meter, the front panel revision number 
is displayed (see table below). 

0 LEDs on

current digit is 0

1 LED on 

current digit is 1

2 LEDs on

current digit is 2

...

...

Press & Hold of the

 BYPASS

 switch will force the unit to reboot.

+

+

VINTAGE DRIVE

1

2

VIOLET EQ

3

HF COMPRESSOR

4

STEREO WIDTH

5

Содержание Fusion




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды