Solid State Logic Fusion страница 21 Скачать руководство пользователя | Manualshive

Страница: 21 / 35

background image

Fusion User Guide

Settings Mode & Factory Reset

16

Settings Mode & Factory Reset

This section will detail how to enter Fusion's Settings Mode and the functionality that can be changed. It also details how to reset
Fusion back to a factory default state.

Entering Settings Mode

To enter the Settings Mode, switch the unit on then hold down the

TRANSFORMER

and

BYPASS

switches during the startup LED

sequence. In this mode it is possible to modify some parameters of the unit. These parameters will be recalled each time the unit
is rebooted.

Brightness

Whilst in Settings Mode, it is possible to select five levels of brightness for the meters and switches.

➤

To decrease the brightness, press the

VINTAGE DRIVE IN

switch.

➤

To increase the brightness, press the

VIOLET EQ IN

switch.

If the

VINTAGE DRIVE IN

switch is not lit, minimum brightness is reached. If the

VIOLET EQ

switch is not lit, maximum brightness

is reached. Factory setting: maximum brightness.

Note: The brightness setting does not affect the startup LED sequence, or signal indicator LEDs found in the

VINTAGE DRIVE

and

HF COMPRESSOR

sections.

Relay Feedback

Whilst in Settings Mode, it is possible to enable or disable the relay feedback of the switches. This affects the startup sequence
and normal operation. To switch between enabled and disabled, press the

INSERT IN

switch.

➤

If

INSERT

is dimly lit white, relay feedback is disabled.

➤

If

INSERT

is lit blue, relay feedback is enabled (a quick relay transition is reproduced as confirmation of the setting).

Factory setting: relay feedback enabled.

Exiting Settings Mode

To exit Settings Mode, press and hold the

BYPASS

switch until the unit reboots.

+

+

«
...
19
20
21
22
23
...
»

Содержание Fusion




































Отзывы:

Нет отзывов

Похожие инструкции для Fusion

Бренд: ABB Страницы: 50

ACS880-01 Series

Бренд: ABB Страницы: 17

Бренд: ABB Страницы: 36

FX-ARM CONTROLLER

Бренд: Magicfx Страницы: 16

The Wave Transformer

Бренд: EarthQuaker Devices Страницы: 21

Бренд: Nellcor Страницы: 161

OXIMAX N-600X Series

Бренд: Nellcor Страницы: 210

Бренд: OAKWORKS Страницы: 24

Бренд: Omlet Страницы: 2

Бренд: Omicron Страницы: 382

Бренд: Omicron Страницы: 188

Бренд: ParaBody Страницы: 6

Бренд: ParaBody Страницы: 11

Бренд: Abus Страницы: 12

Бренд: FARM-MAXX Страницы: 35

LED PowerBank 48

Бренд: SHOWTEC Страницы: 12

Бренд: Harris Страницы: 21

Бренд: Coba Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды