Solid State Logic C100HDSS Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 64

background image

Air Conditioning Requirements

Air conditioning will almost certainly be required for both the Machine and Control rooms in order to maintain the

temperature and humidity to within the required levels.
Power dissipation figures for console control surface and equipment rack are listed in Appendix A.
Appendix E contains the environmental specification for SSL equipment.

Cable Ducting

Cable ducting will be required between the console and the Machine room (as well as to any outboard racks and the

recording areas). The ducting provided should be of sufficient size such that approximately 50mm x 35mm is available for

console surface connection. This should be sufficient for the analogue and digital cabling for metering and the T/B Mic etc.

in addition to the console connections.
The connectors for all control and interface cables are located beneath the console’s Centre Section. The connector

panels are orientated so that cables will exit downwards at the rear of the desk. It is not possible to route cables through

the console legs.
The mains input connectors are located on a separate panel. This panel is normally positioned in the bay to the left of the

Centre Section.

Service Access

Access to all electronic assemblies within the frame is from either the front or above the console. The power supplies are

located in the knee panel area. There are PCB assemblies located behind the channel TFT meter screens. To remove a

TFT screen it will be necessary to remove the top trim. This trim is secured using screws along the rear of the top edge.

If the console is being built into restricted space – as in some mobile installations – then allow sufficient clearance above

the top trim for access to the fixing screws.
Clearance for service access will also be required in front of and behind the rack into which the Blackrock processor is

installed so that cards can easily be removed. See the drawing on page 10 for minimum clearances.

Pre Installation Information

Section 3

Page 9

«
...
11
12
13
14
15
...
»

Содержание C100HDSS

































































Отзывы:

Нет отзывов

Похожие инструкции для C100HDSS

Бренд: Makita Страницы: 7

Бренд: Makita Страницы: 9

Бренд: Makita Страницы: 7

Бренд: Bailey Страницы: 103

Бренд: Hamilton Beach Страницы: 5

Бренд: Hamilton Beach Страницы: 20

Бренд: Hamilton Beach Страницы: 8

Бренд: VAS Страницы: 16

Бренд: Varimixer Страницы: 8

Бренд: Zeppelin Design Labs Страницы: 28

Бренд: Yamaha Страницы: 58

Бренд: Breville Страницы: 20

Бренд: Yamaha Страницы: 40

Fluid Rower FDF

Бренд: First Degree Fitness Страницы: 14

Бренд: TL Audio Страницы: 21

SUPER BAWL WHINE-O-WAH with THMBS

Бренд: D'Andrea Страницы: 2

6 Speed Hand Mixer

Бренд: Oster Страницы: 2

Бренд: Avid Technology Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды