23
Appendix C: Regulatory Information
1. FCC Radio Frequency Interference Statement
FCC ID: KA358WAN3
This device is certified to comply with Part 15 of Federal Communications
Commission (FCC) Rules. Operation is subject to the following two conditions:
1. It may not cause harmful interference.
2. It must accept any interference that may cause undesired operation.
Changes or modifications not expressly approved by Solectek could void the
user’s authority to operate the equipment.
2. U.S. Government Restricted Rights Legend
The Product is provided with Restricted Rights. Use, duplication, reproduction or
disclosure by the Government is subject to restrictions in subdivision (c)(1)(ii)
of the Rights in Technical Data and Computer Product clause at 252.227-7013
and in subparagraphs (a) through (d) of the Commercial Product-Restricted
Rights Clause at 52.227-19. Contractor/Manufacturer is Solectek, 6370 Nancy
Ridge Drive, Suite 109, San Diego, California.
3. Radio Transmission Notice
This product is a low power (less than 1 Watt), OFDM radio system pre-set to
transmit and receive signals in the 5.725 – 5.850 GHz frequency band. This
product has been certified by the U.S. Federal Communications Commission for
use in the United States of America in that band. Other markings on the unit
label shall indicate regulatory compliance in other international areas.
Any prospective user of this product outside the United States of America
should, prior to such use, contact the government department or other agency
responsible for assigning radio frequencies in the country in which use is
proposed to determine whether such department or agency has any objection
to operation of the product given current regulatory label markings on said
product, and whether there are any other local devices generating signals in
that band which might be expected to interfere with the operation of this
product.
Solectek shall not be responsible for any operation of this product which is in
violation of local law, creates interference harmful to other local devices, or
results in a malfunction of this product caused by outside interference.
This device must be professionally installed and used in strict
accordance with the manufacturer's instructions. The installer shall be
responsible for ensuring that the proper antenna is employed so that
the limits in this part are not exceeded, including the requirements of
FCC Part 15.203
However, there is no guarantee that interference to radio communications will
not occur in a particular commercial installation. In case the device does cause
harmful interference with an authorized radio service, the user/ operator shall
promptly stop operating the device until harmful interference has been limited.
Solectek Corporation is not responsible for any radio or television interference
caused by unauthorized modification of this device or the substitution or
attachment of connecting cables and equipment other than specified by
Solectek Corporation. The correction of interference caused by such
unauthorized modification, substitution, or attachment will be the responsibility
of the user.
Warning:
The antennas used for this transmitter must be installed to provide a
separation distance of at least 100 cm from all persons and must not be
co-located or operating in conjunction with any other antenna or
transmitter
This device has been designed to operate with the antennas listed
below, and having a maximum gain of 29 dBi. Antennas not included in
this list or having a gain greater than 29 dBi are strictly prohibited for
use with this device. The required antenna impedance is 50 ohms.
1. Pulse 10dBi RO5810NM (3) 5.8 GHz Radome Omni 10 dBi
2. ARC Wireless Solutions 5.15-5.875GHz 24/23dBi Dual Polarization
Panel Antenna
3. Laird HD Series High Performance Dish Antenna HDDA5W-29-DP -
29dBi dual polarity (H and V)
The use of Antennas #2 and #3 above shall be restricted to Point-to-
Point use only.
This equipment has been tested and found comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
