Sole Diesel 29 GS Скачать руководство пользователя

Страница: 44 / 82

Solé, S.A. C-243 b, km 2 · 08760 Martorell (Barcelona) ·Tel. +34 93 775 14 00 · www.solediesel.com · [email protected]

Marine Diesel gensets.

Operator’s Manual.

Troubleshooting

GENSET FAILURE

SYSTEM

PROBABLE CAUSES

RECOMMENDED ACTIONS

GENERAL

The fuel regulator is not operational.

Contact an Official Solé Diesel Service.

Faulty or clogged fuel pump

Check fuel pump inlet.

Clogged fuel filter

Replace fuel filter.

Air in fuel system

Bleed fuel system.

Incorrect injection pump setting

Contact an Official Solé Diesel Service.

Closed fuel outlet tap

Open the fuel outlet tap.

COOLING SYSTEM

Low cooling liquid level.

Check cooling liquid level and fill tank if necessary.

Faulty stop solenoid (ETR).

Check stop solenoid and replace it if necessary.

Pressed emergency stop button.

Reset the emergency stop button position.

Control panel start signal.

Check the start signal from the controller (yellow wire).

INLET AND EXHAUST

SYSTEM

Dirty or clogged air filter.

Replace the air filter element.

Clogged fuel filter.

Replace fuel filter.

Dirty or faulty fuel injectors.

Clean, test and/or replace fuel injector which is not operating
properly.

Incorrect injection pump setting.

Contact an Official Solé Diesel Service.

INLET AND EXHAUST

SYSTEM

Clogged air filter.

Replace the air filter element.

GENERAL

Incorrect valve clearance.

Perform valve adjustment.

LUBRICATION SYSTEM

Oil level too high.

Check the lubrication oil level and reset it.

Faulty oil pump.

Contact our dealer

Strangled oil pressure-relief valve.

Clean the valve and check its operation.

Oil pressure too low.

Check oil level.

Oil level too low.

Reset oil level. Inspect the marine generator set for leaks.

Faulty oil pressure valve.

Contact an Official Solé Diesel Service.

Faulty pressure gauge, pressure sensor and/or
pressure switch.

Check and/or replace elements.

Engine tilt above allowable values.

Check the engine installation inclination. Reinstall the engine if
necessary.

BLACK SMOKE

FUEL SYSTEM

LUBRICATION SYSTEM

BLUE SMOKE

STARTS AND THEN

STOPS

ELECTRICAL SYSTEM

(CC)

FUEL SYSTEM

LOW OIL PRESSURE

Содержание 29 GS



















































































Результаты поиска

Содержание 29 GS

Отзывы:

Похожие инструкции для 29 GS

Бренды по названию

Популярные бренды

Sole Diesel 29 GS, Руководство оператора

Результаты поиска

Содержание 29 GS

Отзывы:

Похожие инструкции для 29 GS

Бренды по названию

Популярные бренды