Sole Diesel 29 GS страница 20 Скачать руководство пользователя

Страница: 20 / 82

Solé, S.A. C-243 b, km 2 · 08760 Martorell (Barcelona) ·Tel. +34 93 775 14 00 · www.solediesel.com · [email protected]

Marine Diesel gensets. Operator’s Manual.

Installation

Section 3

–

Installation

3.1.

Angle of Installation

Make sure the genset is installed on a level surface. Otherwise, the following angular operation

maximum is permitted:

Continuously

Temporary

29 GSC / 32 GSAC / 35 GTC / 40 GTAC / 45 GTC / 54

GTAC / 50 GTC / 60 GTAC / 68 GTC / 84 GTAC

15º

25º (max. 30 min.)

If the genset operates in these conditions, check

Section 5.4. Lubrication System

3.2.

Genset installation

Follow these steps to install the genset:

Fix genset.

See 9.4 Genset Dimensions

(mounting holes) and

Section 8 Tightening Torques

Connect exhaust outlet. See

9.4 Genset Dimensions

Wet exhaust outlet

Dry exhaust Seawater outlet

Connect siphon breaker. (If installed) See

9.4 Genset Dimensions and 5.7 Inlet and exhaust

system

Connect sweater inlet. See

9.4 Genset Dimensions

Connect fuel inlet. See

9.4 Genset Dimensions

Connect leak coolant outlet. See

9.4 Genset Dimensions

Fill the lubrication circuit with an adequate oil. See

5.4 Lubrication System

Fill the cooling circuit with an adequate coolant. See

5.6 Cooling System

Check each pipe connection for oil or coolant leaks.

10.

Connect to earth. See

5.5 Fuel System

11.

Prime the fuel system. See

5.5 Fuel System

12.

Connect to control panel. See Section

9.4 Genset Dimensions

13.

Connect to the battery. Follow label battery connection into the genset.

It is necessary to install a waterlock (supplied as accessory) in the exhaust system to avoid

water ingestion (See

5.7 Inlet and exhaust system

Содержание 29 GS



















































































Результаты поиска

Содержание 29 GS

Отзывы:

Похожие инструкции для 29 GS

Бренды по названию

Популярные бренды

Sole Diesel 29 GS, Руководство оператора

Результаты поиска

Содержание 29 GS

Отзывы:

Похожие инструкции для 29 GS

Бренды по названию

Популярные бренды