background image

Introduction

Introduction

12

13

3.2 Work Modes

·

In the absence of the external generator, or 

the power is not enough,battery will 
discharge for local loads firstly, and grid will 
supply power when the battery capacity is 
not enough.

     

EPS Status

When the grid is off, system will supply 
emergency power from battery to supply the 
home loads. (Battery is necessary in EPS mode.)

X1-Retro Fit Series inverter provides multiple work modes based on different 
requirements.

Work modes:  

Feed in Priority

Priority:load>grid>battery

This mode applies the area that has high 
feed-in tariff and export control.

Work modes:  

Back up mode

Priority:battery>load>grid

This mode applies the area that has frequent 
power outages. And  this mode ensures the 
battery will has enough energy to supply when 
the grid is off.

Work modes:  

Self-use 

Priority: load>battery>grid

This mode applies the area that has low feed-
in tariff and high energy price.

Work modes:  

Force time use

Priority:battery>load>grid

(when charging)

Priority:load>battery>grid

(when discharg-

ing)
This mode applies the area that has electricity 
price between peak and valley. User can use 
off-peak electricity to charge the battery. 

·

In the case of the external generator, the 

power generated will be used to supply the 
local loads firstly, then to charge the battery. 
The redundant power will export to the 
public grid.

·

The charging and discharging time can be 

set flexibly. 

3.3 Dimension

464.0mm

4

7

6

.0 m

m

180.0 mm

·

In the case of the external generator, the 

power generated  will be used to supply the 
local loads firstly, then export to the public 
grid. The redundant power will charge the 
battery.
·In the absence of the external generator, or 

the power is not enough,battery will discharge 
for local loads firstly, and grid will supply power 
when the battery capacity and power 
generation is not enough.

·

In the case of external power generation 

equipment, the power generated  will be used 
to charge the battery fully firstly, then supply 
the local loads. The redundant power will 
export to the public grid.

·

In the absence of an external power 

generation device, charge the battery with the 
public grid.

·

The inverter will switch to EPS mode only 

when the grid is abnormal.

Содержание X1-Retro Fit







































Отзывы: