SNOWJOE 24V-X2-SB15, Руководство оператора

Страница: 15 / 20

15
1. Open the left side plate by removing the 4 screws
(Fig. 21).
2. Remove the old belt as indicated in step 3 from last
section (Fig. 18).
3. Put the new belt on the drive pulley first and then place
the belt at the lower end of the auger pulley. Use your
right hand to press the belt with the ribbed side down.
While holding the belt down with your right hand, use your
left hand to turn the auger forward so that the auger pulley
rotates in a clockwise direction. The belt will be gradually
pushed down onto the pulley. When the belt is seated on
the pulley, adjust it so that the ribs of the belt match the
grooves on the pulley (Fig. 22).
4. After the belt is installed, replace the side cover and
secure it with the 4 screws (Fig. 21).
NOTE: Heavy wet snow puts a load on belts, thus
requiring more frequent belt replacement.
Proper Care for Bat Charger
m
WARNING!
To reduce the risk of injury, always unplug
the charger and remove the battery packs from the charger
before performing any maintenance task. Never disassemble
the battery packs or charger. Contact your Snow Joe
®
+
Sun Joe
®
dealer or the Snow Joe
®
+ Sun Joe
®
customer
service center for ALL repairs.
1. To reduce the risk of injury and damage, never immerse
your battery packs or charger in liquid or allow any liquid
to flow inside these components.
2. Clean out dust and debris from charger vents and
electrical contacts by blowing with compressed air.
3. Use only mild soap on a damp cloth to clean the battery
packs and charger, keeping away from all electrical
contacts. Certain cleaning agents and solvents are
harmful to plastics and other insulated parts. Some of
these include gasoline, turpentine, lacquer thinner, paint
thinner, chlorinated cleaning solvents, ammonia and
household detergents containing ammonia. Never use
flammable or combustible solvents around battery packs,
battery chargers or tools.
4. The 24V iON+ lithium-ion battery charger has no
serviceable parts.
Storage
1. Run the machine a few minutes after throwing snow to
prevent the auger from freezing.
2. Examine the cordless snow blower thoroughly for worn,
loose or damaged parts. Should you need to repair or
replace a part, contact an authorized Snow Joe
®
+
Sun Joe
®
dealer or call the Snow Joe
®
+ Sun Joe
®
customer service center at 1-866-SNOWJOE
(1-866-766-9563) for assistance.
3. Clean the snow blower before storing or transporting.
Be sure to secure the unit while transporting.
4. Remove the batteries from the cordless snow blower
before storing.
5. Store the cordless snow blower indoors in a locked,
dry place out of the reach of children to prevent
unauthorized use or damage.
6. Maintain safety and instruction labels, as necessary.
7. Always refer to the B Charger Off-Season Storage
section for important details if the snow blower is to be
stored for an extended period.
B Charger Off-Season Storage
1. Do not expose your battery packs or charger to water,
rain or allow them to get wet. This could permanently
damage the charger and the battery packs. Do not use oil
or solvents to clean or lubricate your battery packs as the
plastic casing can become brittle and crack, causing a
serious risk of injury.
2. Store the battery packs and charger at room temperature
away from moisture. Do not store in damp locations where
corrosion of terminals may occur. As with other battery
pack types, permanent capacity loss can result if the pack
is stored for long periods of time at high temperatures
(over 120ºF/49ºC).
3. 24V iON+ lithium-ion battery packs maintain their charge
during storage longer than other battery pack types.
As a general practice, it is best to unplug the battery
charger and remove the battery packs when they are not
in use. Recharge the battery packs every 6 months to
Fig. 21
Left side plate
Screws
Fig. 22
New belt Drive pulley
Auger pulley