background image

Lit. No. 76454/76455/76456, Rev. 03 

12 

February 15, 2020

MOUNTING THE SPREADER

4. 

Install the chute/deflector assembly to the spinner 

assembly using the four 5/16" x 1-1/2" tapping 

screws and 5/16" locknuts in the supplied 

hardware kit to complete the drive assembly.

5.  Mount the drive assembly to the spreader using 

the 1/2" x 17-5/8" bent pin and secure it with the 

2-3/8" hairpin cotter. Ensure that the bent pin 

passes through the small center mounting tab on 

the auger drive enclosure.

6. 

Slide the spreader forward until the deflector/chute 

assembly makes contact with the vehicle. Then 

slide spreader back approximately 1" to allow 

proper clearance.

7.  Once the spreader is positioned front to back in 

the vehicle bed, center it left to right.

8.  Looking at the inside corners of the spreader 

frame, you will notice four holes in the bottom of 

the frame. Using a paint pen or similar marking 

device, mark the hole locations on the vehicle bed. 

 

If mounting holes cannot be drilled in the 

marked locations,

 install the optional mounting 

bars to the spreader frame using the supplied 

1/2" x 1-1/2" carriage bolts and 1/2" locknuts. Use 

the existing holes in the mounting bars to mark 

drilling locations on the vehicle bed. 

MOUNTING THE SPREADER

NOTE: Periodically throughout the snow and ice 

control season, verify that mounting devices are 

secure.

1.  Remove the tailgate from the UTV bed.

2.  Load the spreader onto the UTV bed.

3. 

Assemble the chute to the deflector using the 

four 1/4" x 3/4" serrated flange cap screws and 

1/4" locknuts in the supplied hardware kit.

 WARNING

Spreader shall be bolted to vehicle frame. 

Do not rely on the tie‑down chains or straps 

alone to hold spreader in vehicle.

 CAUTION

Before lifting, verify that hopper is empty of 

material. The lifting device must be able to 

support the spreader's weight.

Deflector

Chute

Deflector

Spinner 

Assembly

Содержание V-Pro SP-2000





















Отзывы: