background image

Lit. No. 76454/76455/76456, Rev. 03 

February 15, 2020

SAFETY

FIRE AND EXPLOSION

Be careful when using gasoline. Do not use gasoline 

to clean parts. Store only in approved containers away 

from sources of heat or flame.

CELL PHONES

A driver's first responsibility is the safe operation of 

the vehicle. The most important thing you can do 

to prevent a crash is to avoid distractions and pay 

attention to the road. Wait until it is safe to operate 

Mobile Communication Equipment such as cell phones, 

text messaging devices, pagers, or two-way radios.

VENTILATION

BATTERY SAFETY

 WARNING

Gasoline is highly flammable and gasoline 

vapor is explosive. Never smoke while 

working on vehicle. Keep all open flames 

away from gasoline tank and lines. Wipe up 

any spilled gasoline immediately.

 CAUTION

Batteries normally produce explosive gases 

which can cause personal injury. Therefore, 

do not allow flames, sparks, or lit tobacco 

to come near the battery. When charging or 

working near a battery, always cover your 

face and protect your eyes, and also provide 

ventilation.

•  Batteries contain sulfuric acid, which burns 

skin, eyes, and clothing.

•  Disconnect the battery before removing or 

replacing any electrical components.

 WARNING

Vehicle exhaust contains lethal fumes. Breathing  

these fumes, even in low concentrations,  

can cause death. Never operate a vehicle in 

an enclosed area without venting exhaust to 

the outside.

FUSES

The electrical system contains several automotive-style 

fuses. If a problem should occur and fuse replacement 

is necessary, the replacement fuse must be of the 

same type and amperage rating as the original. 

Installing a fuse with a higher rating can damage the 

system and could start a fire.

PERSONAL SAFETY

•  Remove ignition key and put the vehicle in PARK 

or in gear to prevent others from starting the 

vehicle during installation or service.

• 

Wear only snug-fitting clothing while working on 

your vehicle or spreader.

•  Do not wear jewelry or a necktie, and secure  

long hair.

•  Wear safety goggles to protect your eyes from 

battery acid, gasoline, dirt, and dust.

•  Avoid touching hot surfaces such as the engine, 

radiator, hoses, and exhaust pipes.

• 

Always have a fire extinguisher rated BC handy, 

for flammable liquids and electrical fires.

Содержание V-Pro SP-2000





















Отзывы: