Snorkel SL26RTE, Руководство пользователя

Страница: 133 / 209

Page 3 - 3 SL26/30SL
PREVENTATIVE MAINTENANCE TABLE
INTERVAL
Daily = each shift or everyday
50 hrs/30 d = every 50 hours or 30 days
250 hrs/6 m = every 250 hours or 6 months
1000 hrs/2 y = every 1000 hours or 2 years
Y = Yes/Acceptable
N = No/Not Acceptable
R = Repaired/Acceptable
DO NOT
fit replacement parts other than genuine components without express written approval
from the manufacturer.
SERVICE AND REPAIR
PREVENTATIVE MAINTENANCE REPORT
Date:
Owner:
Model #:
Serial #:
Serviced By:
Service Interval:
COMPONENT INSPECTION OR SERVICES INTERVAL Y N R
Battery
System
Check electrolyte level Daily
Check specific gravity
6m
Clean exterior 6m
Check battery cable condition Daily
Clean terminals 6m
Engine Oil
Check level and condition Daily
Check for leaks Daily
Change oil filter
30d
Engine
Fuel system
Check fuel level Daily
Check for leaks Daily
Replace fuel filter
6m
Check air cleaner Daily
Engine
Coolant
Check coolant level
(with engine cold)
Daily
Replace coolant 3m
Hydraulic Oil
Check oil level Daily
Change filter
6m
Drain and replace oil 2y
Hydraulic
system
Check for leaks Daily
Check hose connections 30d
Check hoses for exterior wear 30d
Emergency
hydraulic
System
Operate the emergency lowering valve and
check for serviceability Daily
Controller Check switch operation Daily
Control Cable Check the exterior of the cable for pinching,
binding or wear
Daily
Platform deck
and rails
Check fasteners for proper torque Daily
Check welds for cracks Daily
Check condition of deck Daily
Tyres
Check for damage Daily
Check lug nuts (torque to 122 Nm/90 ft. lbs.) 30d
Hydraulic
pump
Wipe clean 30d
Check for leaks at mating surfaces 30d
Check for hose fitting leaks
Daily
Check mounting bolts for proper torque 30d
Entire
unit
Check for and repair collision damage Daily
Check fasteners for proper torque 3m
Check for corrosion-remove and paint 6m
Lubricate 30d
COMPONENT INSPECTION OR SERVICES INTERVAL Y N R
Drive Motors Check for operation and leaks Daily
Steering
system
Check hardware & fittings for proper
torque
6m
Grease pivot pins 30d
Oil king pins 30d
Check steering cylinder for leaks 30d
Elevating
Assembly
Inspect for structural cracks Daily
Check pivot points for wear 30d
Check mounting pin pivot bolts for
proper torque
30d
Check linkage gear for wear 6m
Check elevating arms for bending 6m
Grease linkage pins 30d
Grease linkage gear 30d
Chassis
Check hoses for pinch or rubbing
points
Daily
Check component mounting for
proper torque
6m
Check welds for cracks Daily
Lift Cylinder
Check the cylinder rod for wear 30d
Check mounting pin pivot bolts for
proper torque
30d
Check seals for leaks 30d
Inspect pivot points for wear 30d
Check fittings for proper torque
30d
Fore/Aft cylinder &
side/side cylinder
Check the cylinder rod for wear 30d
Check mounting pin pivot bolts for
proper torque
30d
Check seals for leaks 30d
Inspect pivot points for wear 30d
Check fittings for proper torque
30d
Axle
cylinder
Check the cylinder rod for wear 30d
Check mounting pin pivot bolts for
proper torque
30d
Check seals for leaks 30d
Inspect pivot points for wear 30d
Check fittings for proper torque
30d
Labels Check for peeling, missing or unread-
able labels & replace
Daily
Wheel bearings Replace wheel bearings (replace
wheel bearings and seals at 2000
hours)
2y
Table 3-1 : Preventative maintenance checklist
A thorough investigation should be carried out every 6 months.
NOTE: Frequency and extent of periodic examinations may depend on national regulations.
Fitment of any component other than approved items designed for use with this machine can result
in serious danger to operators, property and bystanders.