background image

ML5I • ML10I • ML15I • ML20I • ML25I – 7030242  

13 

Chapter 5 – Operation

Danger

The material lift is not electrically insulated. Death 

or serious injury will result from contact with, or 

inadequate clearance from, an energized conductor. 

Do not go closer than the minimum safe approach 

distance as defined by ANSI.

Warning

Pinch points may exist between moving components. 

Death or serious injury could result from becoming 

trapped between components, buildings, structures, 

or other obstacles. Make sure there is sufficient clear

-

ance around the machine before moving the material 

lift. Allow sufficient room and time to stop movement 

to avoid contact with structures or other hazards.

The material lift can tip over if it becomes unstable. 

Death or serious injury could result from a tip-over 

accident. Operate the material lift on a firm, flat, level 

surfaces. Do not position the material lift for elevated 

use near any drop-off, hole, slope, soft or uneven 

ground, or other tip-over hazard.

The maximum load capacity is the total weight of th 

equipment that may be lifted with the material lift forks. 

The maximum load capacity is stated on the lift serial 

plate and is listed in the machine lift specifications in this 

manual.

 

Warning

The material lift can tip over if it becomes unstable. 

Death or serious injury could result from a tip-over 

accident. Do not exceed the load capacity values 

indicated on the machine serial plate and in this 

Operator’s Manual.

Capacity values indicate the rated lifting capacity and do 

not indicate material lift stability.

The operator bears ultimate responsibility for ensuring 

that the material lift is properly set up for the particular 

conditions encountered.

This section provides instructions for the safe and proper 

operation of the material lift. It is the responsibility of the 

operator to follow these instructions. Failure to follow 

these instructions, as well as all safety rules in this man-

ual and attached to the material lift may result in serious 

injury or death.

During operation:

 

y

Follow all of the safety rules provided in previous 

sections of this manual.

 

y

Follow all instructions provided in this section.

Set Up

To set up the machine, select an area that is firm, level 

and clear of debris and overhead obstructions.

Follow these steps to set up the machine.

Material lifts equipped with stabilizers

  1. Push down on the stabilizer lock plates to release 

the stabilizers.

  2.  Lower the stabilizers until the casters are in contact 

with the ground.

  3.  Verify that the lock plates are engaged and the sta-

bilizers are locked in the down position.

  4.  Remove the leg retainer pin.

  5.  Lower the leg to the down position.

  6. Insert the leg retainer pin through the leg and the 

base.

  7.  Repeat the above steps to lower and secure the other 

leg.

  8. Place the desired load lifting attachment (standard 

forks, adjustable forks, boom) inside the carriage.

  9. Insert the fork retainer pin through the load lifting 

attachment and the carriage.

 

 

Содержание ML10I





























Отзывы: