Sno-Way 22 Series Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 40

background image

5

16. Apply included dielectric grease to all connectors.

NOTE: An adapter is recommended for vehicles with a
side post battery. (See Figure 1-3). Adapters can be pur-
chased from your Sno-Way dealer, Part #96100773.

Figure 1-3

Mechanical Installation

IMPORTANT:

Graphics and illustrations may be

used which may show equipment and/or options not
included in every installation.

NOTE: The 22 series blade uses blade stops. Make sure
the proper stops are installed.

1. Open the power pack carton and remove the blade

parts bag (part number 96107547). The blade stops are
in the blade parts bag.

2. Place stops between the lugs on the swing frame.

Secure with 3/8" x 1-3/4" bolts and locking nuts. (See
Figure 1-4). The bolts and nuts are in the blade parts bag.

Figure 1-4

3. Lay blade face down on floor.

4. Place swing frame on blade, positioning the two

inside ribs between the swing frame lugs. insert a 3/4" x
1-5/8" clevis pin from blade parts bag to fasten each side.
(See Figure 1-5).

Figure 1-5

5. Insert washer on end of each clevis pin and secure

with cotter pin.

NOTE: Note: Make sure cotter pin is properly bent as in
fig. 1-6 or pin may work loose.

WARNING

Failure to connect the main light harness on the
truck when plow is not attached will cause truck
lights to not operate, which could cause an
accident.

FAILURE TO HEED CAN RESULT IN INJURY

OR DEATH.

ADAPTER

2’ RED

BATTERY CABLE

3/8"x 1-3/4" BOLT

3/8"x 1-3/4" BOLT

3/8" NYLOCK NUT

3/8" NYLOCK NUT

3/4" x 1-5/8"

CLEVIS PIN

WASHER

WASHER

COTTER

PIN

COTTER

PIN

3/4" x 1-5/8"

CLEVIS PIN

«
...
4
5
6
7
8
...
»

Содержание 22 Series









































Отзывы:

Нет отзывов

Похожие инструкции для 22 Series

Бренд: Makita Страницы: 84

Бренд: Makita Страницы: 35

Бренд: Makita Страницы: 6

Бренд: Makita Страницы: 6

Бренд: Makita Страницы: 16

Бренд: Makita Страницы: 148

Бренд: Makita Страницы: 66

Бренд: Makita Страницы: 8

Бренд: Makita Страницы: 9

Бренд: MTD Страницы: 32

Бренд: Yard Machines Страницы: 28

Бренд: Gardena Страницы: 11

Бренд: Black+Decker Страницы: 100

Бренд: Weed Eater Страницы: 24

Snow Line 620E III

Бренд: AL-KO Страницы: 84

Бренд: Ryobi Страницы: 256

Бренд: Kärcher Страницы: 112

Бренд: Troy-Bilt Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды