Sno-Way 22 Series Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 40

background image

4

General

Install the subframe on the vehicle using the instructions
supplied with the subframe package. The pin height
should be 8" - 10" off the ground. (See Figure 1-1).

Figure 1-1

Electrical Installation

1. Remove the battery power harness and power

harness parts bag from the power pack box.

NOTE: Take extra time needed to plan the routing of wir-
ing harnesses. Make sure harnesses do not interfere
with, or contact, any moving parts and route wires away
from excessive heat areas. Read all the instructions
carefully to ensure a safe and professional installation.

2. Mount the fuse holder near the battery using (2) #10

x 1" self-tapping screws.

3. Take the cover off of the fuse holder and remove the

nuts on the studs. Place one end of the 2 ft. long power
wire on one stud. (See Figure 1-2).

Figure 1-2

4. Attach the other end of one 2 ft. long power wire to

the positive terminal on the battery.

5. Attach the power harness red wire to the other

terminal of the fuse holder.

6. Place the fuse between the two studs and replace the

nuts and cover.

7. Route power harness to convenient point on front of

vehicle for connection to plow.

8. Attach the power harness black wire to the NEG. (-)

terminal of the battery and re-connect the negative
battery terminal.

9. Spray all terminal connections with a battery terminal

protective coating.

10. Secure harness with plastic tie straps.

11. Install truck control harness if needed, using

instructions included with controls.

12. Remove the main light harness from the power pack

carton. Route the harness from the headlights to the front
of the truck and through the grille or bumper. The ends
with the green plugs go to the headlights and the ends
with the black plugs go to the front of the truck.

13. Open the adapter harness bag, remove the harness

and plug the proper adapters into the green plugs on the
main harness. Connect the adapters to the truck wiring
following the included instructions.

14. Secure the main harness and adapters. Make sure

that the harnesses are not in contact with moving or hot
engine parts.

15. Plug the male and female black plugs at the front of

the truck together. These must be connected to allow the
truck lights to operate.

WARNING

Disconnect the vehicle NEG. (-) battery cable
while performing steps 2 - 5 to avoid serious
bodily injury from electrical shock, fire, or
explosion. Do not re-connect battery cable until
indicated in step 8.

FAILURE TO FOLLOW CAN RESULT IN INJURY

OR DEATH

8" TO 10" HEIGHT

TRUCK

RED

BLACK

POWER

HARNESS

POWER HARNESS PLUG

BATTERY

FUSE &
FUSE HOLDER

INSTALLATION INSTRUCTIONS

«
...
3
4
5
6
7
...
»

Содержание 22 Series









































Отзывы:

Нет отзывов

Похожие инструкции для 22 Series

Бренд: SNOWJOE Страницы: 24

Бренд: McCulloch Страницы: 12

Бренд: Yard force Страницы: 6

Бренд: White Outdoor Страницы: 28

Бренд: Cub Cadet Страницы: 20

Бренд: Gude Страницы: 32

Бренд: Gude Страницы: 40

Бренд: Milwaukee Страницы: 4

Mini Snow Blade

Бренд: Erskine Attachments Страницы: 20

Бренд: Homelite Страницы: 166

Бренд: Homelite Страницы: 166

Бренд: Maruyama Страницы: 16

Бренд: Ventrac Страницы: 33

Бренд: TrimmerPlus Страницы: 36

Бренд: Columbia Страницы: 28

Бренд: GreenWorks Tools Страницы: 110

Бренд: Yardworks Страницы: 19

Бренд: Padagas Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды