Sno-Way 22 Series Скачать руководство пользователя страница 2

Страница: 2 / 40

TABLE OF CONTENTS

Page

INTRODUCTION ........................................................................................................................ 2

SAFETY ..................................................................................................................................... 3

INSTALLATION INSTRUCTIONS ............................................................................................. 4

Electrical Installation ........................................................................................................ 4

Mechanical Installation..................................................................................................... 5

Mounting Snow Plow To Vehicle ..................................................................................... 8

Installing The Cylinder Lock Clamp .............................................................................. 11

Removing Snow Plow From Vehicle ............................................................................. 12

MAINTENANCE ....................................................................................................................... 14

Break In Period................................................................................................................ 14

To Remove Excessive Free Play.................................................................................... 14

Periodic Inspection ......................................................................................................... 14

Plow Storage ................................................................................................................... 14

Polycarbonate Blade Care ............................................................................................. 15

Polycarbonate Blade Cleaning Instructions................................................................. 15

Plow Light Bulb Replacement

....................................................................................... 15

Fluid Requirements......................................................................................................... 16

Changing Oil and Cleaning Filter Screen ..................................................................... 16

Cutting Edge.................................................................................................................... 18

Disk Shoe Adjustment .................................................................................................... 18

Trip Spring Adjustment .................................................................................................. 18

Blade Stop Replacement ................................................................................................. 18

Emergency Plow Raise.................................................................................................... 18

PLOWING OPERATION .......................................................................................................... 19

Operating Class .............................................................................................................. 19

Before the Season Begins ............................................................................................. 19

Transporting Vehicle With Plow Attached .................................................................... 19

Plowing Like A Pro ......................................................................................................... 19

Using The Down Pressure (DP) Hydraulic Systems .................................................... 20

Clearing Driveways ......................................................................................................... 20

Clearing Parking Lots ..................................................................................................... 20

TROUBLESHOOTING ............................................................................................................. 21

Introduction ..................................................................................................................... 21

Troubleshooting Quick Reference................................................................................. 21

Troubleshooting Guide................................................................................................... 21

THEORY OF OPERATION ...................................................................................................... 27

Hydraulic Power Unit ...................................................................................................... 27

Hydraulic Controls .......................................................................................................... 27

Electro-Hydraulic Operation .......................................................................................... 27

Raise Mode Of Operation ............................................................................................... 27

Lower Mode Of Operation - Gravity Down and Float................................................... 28

Angle Left or Right Mode of Operation ......................................................................... 28

Fuse.................................................................................................................................. 28

HYDRAULIC SCHEMATIC (Gravity Down System) .............................................................. 29

HYDRAULIC SCHEMATIC (Down Pressure System) ........................................................... 30

WIRING SCHEMATIC (Gravity Down System) With S.N. Before 22G100200 ..................... 31

WIRING SCHEMATIC (Down Pressure System) With S.N. Before 22D102000................... 32

PROCONTROL WIRING SCHEMATIC With S.N. After 22G200000 ...................................... 33

PROCONTROL WIRING SCHEMATIC With S.N. After 22D200000....................................... 34

MAIN WIRING HARNESS SCHEMATIC (Energy Interruption System) .............................. 35

TORQUE SPECIFICATIONS ................................................................................................... 36

Содержание 22 Series









































Результаты поиска

Содержание 22 Series

Отзывы:

Похожие инструкции для 22 Series

Бренды по названию

Популярные бренды

Sno-Way 22 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 22 Series

Отзывы:

Похожие инструкции для 22 Series

Бренды по названию

Популярные бренды