background image

45

Specifications

ENGINE:

25 HP Kawasaki

Make

Kawasaki

Model

FH721V

Horsepower

25 @ 3600 rpm

Displacement

41.2 Cu. in (675 cc)

Electrical System

12 Volt, 13 amp. Alternator, Battery: 340 CCA

Oil Capacity

2.0 US qt. ( 1.9 L) w/ Filter

27 HP Kohler

Make

Kohler

Model

CV740S

Horsepower

27 @ 3600 rpm

Displacement

44.24 Cu. in (725 cc)

Electrical System

12 Volt, 16 amp. Alternator, Battery: 340 CCA

Oil Capacity

2.1 US qt.. (2.0 L) w/ Filter

27 HP Kawasaki

Make

Kawasaki

Model

FX751V

Horsepower

27 @ 3600 rpm

Displacement

52.0 Cu. in (852 cc)

Electrical System

12 Volt, 15 amp. Alternator, Battery: 340 CCA

Oil Capacity

2.0 US qt. ( 1.9 L) w/ Filter

32 HP Briggs & Stratton

Make

Briggs & Stratton

Model

543777-0120-E1

Horsepower

32 @ 3600 rpm

Displacement

54.62 Cu. in (895 cc)

Electrical System

12 Volt, 20 amp. Alternator, Battery: 340 CCA

Oil Capacity

2.4 US qt.. (2.25 L) w/ Filter

CHASSIS:

Fuel Tank 

Capacity: 12 Gallons (45.4 L)

Rear Wheels

Tire Size: 24 x 12.00 -12
Inflation Pressure: 15 psi (1,03 bar)

Front Wheels

Tire Size: 13 x 6.50 - 6
Inflation Pressure: 25 psi (1,72 bar)

TRANSMISSIONS:
HydroGear PG-3H / HGM-12E 3131

Type

Pump and Wheel Motor

Hydraulic Fluid

SAE 20W-50 motor oil

Speeds

Forward: 0-10 MPH (0-16.09 km/h)

@ 3400 rpm

Reverse: 0-5 MPH (0-8.05 km/h)

Continuous Torque

222 ft. lbs. (301 N.m.)

Output
Maximum Weight 

750 lbs. (340 Kg)

on Axle

NOTE: Specifications are correct at time of printing and are subject to change without notice.

*Actual sustained equipment horsepower will likely be lower due to operating limitations and environmental factors.

Specifications

Engine Power Rating Information

The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive Engineers)
code J1940 (Small Engine Power & Torque Rating Procedure), and rating performance has been obtained and corrected in
accordance with SAE J1995 (Revision 2002-05). Torque values are derived at 3060 RPM; horsepower values are derived at
3600 RPM. Actual gross engine power will be lower and is affected by, among other things, ambient operating conditions and
engine-to-engine variability. Given both the wide array of products on which engines are placed and the variety of
environmental issues applicable to operating the equipment, the gas engine will not develop the rated gross power when used
in a given piece of power equipment (actual "on-site" or net power). This difference is due to a variety of factors including, but
not limited to, accessories (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations,
ambient operating conditions (temperature, humidity, altitude), and engine-to-engine variability.  Due to manufacturing and
capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this Series engine.

Specifications

Содержание S200XKAV2561


















































Отзывы: