background image

41

Maintenance

Storage

Temporary Storage (30 Days Or Less)

Remember, the fuel tank will still contain some gasoline, so
never store the unit indoors or in any other area where fuel
vapor could travel to any ignition source. Fuel vapor is also
toxic if inhaled, so never store the unit in any structure used
for human or animal habitation.

Here is a checklist of things to do when storing your unit
temporarily or in between uses:

• Keep the unit in an area away from where children may

come into contact with it. If there’s any chance of
unauthorized use, remove the spark plug (s) and put in a
safe place. Be sure the spark plug opening is protected
from foreign objects with a suitable cover.

• If the unit can’t be stored on a reasonable level surface,

chock the wheels.

• Clean all grass and dirt from the mower.

Long Term Storage (Longer Than 30 Days)

Before you store your unit for the off-season, read the
Maintenance and Storage instructions in the Safety Rules
section, then perform the following steps:

1. Drain crankcase oil while engine is hot and refill with a

grade of oil that will be required when unit is used again.

2. Prepare the mower deck for storage as follows:

a. Remove mower deck from the unit.

b. Clean underside of mower deck.

c. Coat all bare metal surfaces with paint or light coat of

oil to prevent rusting.

3. Clean external surfaces and engine.

4. Prepare engine for storage. See engine owner’s 

manual.

5. Clean any dirt or grass from cylinder head cooling fins,

engine housing and air cleaner element.

6. Cover air cleaner and exhaust outlet tightly with plastic

or other waterproof material to keep out moisture, dirt
and insects.

7. Completely grease and oil unit as outlined in the Normal

Care section.

8. Clean up unit and apply paint or rust preventative to any

areas where paint is chipped or damaged.

9. Be sure the battery is filled to the proper level with water

and is fully charged. Battery life will be increased if it is
removed, put in a cool, dry place and fully charged
about once a month. If battery is left in unit, disconnect
the negative cable.

WARNING

Never store the unit, with gasoline in engine or fuel
tank, in a heated shelter or in enclosed, poorly
ventilated enclosures. Gasoline fumes may reach an
open flame, spark or pilot light (such as a furnace,
water heater, clothes dryer, etc.) and cause an
explosion.

Handle gasoline carefully. It is highly flammable and
careless use could result in serious fire damage to
your person or property.

Drain fuel into an approved container outdoors away
from open flame or sparks.

10. Drain fuel system completely or add a gasoline stabilizer

to the fuel system. If you have chosen to use a fuel
stabilizer and have not drained the fuel system, follow all
safety instructions and storage precautions in this
manual to prevent the possibility of fire from the ignition
of gasoline fumes. Remember, gasoline fumes can travel
to distant sources of ignition and ignite, causing risk of
explosion and fire.

NOTE: Gasoline, if permitted to stand unused for extended
periods (30 days or more), may develop gummy deposits
which can adversely affect the engine carburetor and cause
engine malfunction. To avoid this condition, add a gasoline
stabilizer to the fuel tank and run the engine a few minutes,
or drain all fuel from the unit before placing it in storage.

Starting After Long Term Storage

Before starting the unit after it has been stored for a long
period of time, perform the following steps.

1. Remove any blocks from under the unit.

2. Install the battery if it was removed.

3. Unplug the exhaust outlet and air cleaner.

4. Fill the fuel tank with fresh gasoline. See engine  

manual for recommendations.

5. See engine owner’s manual and follow all instructions

for preparing engine after storage.

6. Check crankcase oil level and add proper oil if 

necessary. If any condensation has developed during
storage, drain crankcase oil and refill.

7. Inflate tires to proper pressure. Check fluid levels.

8. Start the engine and let it run slowly. DO NOT run at

high speed immediately after starting. Be sure to run
engine only outdoors or in well ventilated area.

Regular Maintenance

Содержание S200XKAV2561


















































Отзывы: