Snapper 5900528 Скачать руководство пользователя страница 42

Страница: 42 / 48

Not for

Reproduction

Rider Troubleshooting Continued.

Problem Cause

Remedy

Engine runs, but rider will

1. Transmission release lever(s)

1. Move the transmission release lever(s) to

not drive.

in “open” position.

the “closed” position.

2. Belt is broken.

2. See Drive Belt Replacement.

3. Drive belt slips.

3. See problem and cause below.

4. Brake is not fully released.

4. See authorized service dealer

Rider drive belt slips.

1. Pulleys or belt greasy or oily.

1. Clean as required.

2. Tension too loose.

2. Adjust spring tension.

See Drive Belt Replacement

3. Belt stretched or worn.

3. Replace belt.

Brake will not hold.

1. Brake is incorrectly adjusted.

1. See Brake Adjustment.

2. Brake pads worn.

2. Replace with new brake pads.

Rider steers or handles poorly.

1. Steering linkage is loose.

1. Check and tighten any loose connections.

2. Improper tire inflation.

2. See Regular Maintenance Section.

Troubleshooting the Mower

Problem Cause

Remedy

Mower will not raise.

1. Lift linkage not properly attached

1. See authorized service dealer for repair.

or damaged.

Engine stalls easily with

1. Engine speed too slow.

1. Set to full throttle.

mower engaged.

2. Ground speed too fast.

2. Decrease Ground Speed.

3. Cutting height set too low.

3. Cut tall grass at maximum cutting

height during first pass.

4. Discharge chute jamming

4. Cut grass with discharge pointing toward

with cut grass.

previously cut area.

Excessive mower vibration.

1. Blade mounting bolts are loose.

1. Tighten to 70 ft.lbs. (94 N.m.).

2. Mower blades, arbors,

2. Check and replace as necessary.

or pulleys are bent.

3. Mower blades are out

3. Remove, sharpen, and balance blades.

of balance.

See Maintenance Section.

4. Belt installed incorrectly.

4. Reinstall Correctly.

Excessive belt wear or breakage.

1. Bent or rough pulleys.

1. Repair or replace.

2. Using incorrect belt.

2. Replace with correct belt.

Mower drive belt slips

1. Idler pulley spring broken or not

1. Repair or replace as needed.

or fails to drive.

properly attached.

2. Mower drive belt broken.

2. Replace drive belt.

Mower does not engage.

1. Electrical wiring damage.

1. Locate & repair damaged wire.

2. PTO clutch not adjusted

2. See PTO Clutch Adjustment section

3. Battery voltage too low.

3. Recharge battery and check alternator.

See Battery Maintenance section.

www.SnapperPro.com

Troubleshooting

Содержание 5900528

















































Результаты поиска

Содержание 5900528

Отзывы:

Похожие инструкции для 5900528

Бренды по названию

Популярные бренды

Snapper 5900528, Руководство оператора

Результаты поиска

Содержание 5900528

Отзывы:

Похожие инструкции для 5900528

Бренды по названию

Популярные бренды