Snapper 400ZB2548 Скачать руководство пользователя | Manualshive

Страница: 32 / 48

background image

Return-to-Neutral Adjustment

To determine if it is necessary to adjust the neutral return,
perform the following steps.

1. Disengage the PTO, engage the parking brake and turn

off the engine.

2. Move the ground speed control levers into the operating

position, pull the levers rearward and release.

3. Move the ground speed control levers out towards the

neutral position. If the levers do not align with the
notches in the neutral lock plate, it is necessary to adjust
the neutral return rod (B, Figure 35).

Adjustment

1. Disengage the PTO, engage the parking brake and turn

off the engine.

2. There are three jam nuts (A, Figure 35) on the linkage

rod (B). The first two are used together to turn the rod
and the third (towards the front of the machine) is used
to lock the rod in place. Loosen the jam nut that locks
against the ball joint and turn the linkage rod to adjust.
If the machine creeps forward, turn the linkage rod
CLOCKWISE (while standing at the rear of the machine,
facing forward). If the machine creeps backward, turn
the rod COUNTER-CLOCKWISE.

30

www.SnapperPro.com

Regular Maintenance

Figure 35. Return-to-Neutral Adjustment
A. Jam Nuts
B. Neutral Return Rod

B

A

WARNING

To avoid serious injury, perform adjustments only with
the engine stopped, the key removed and the tractor on
level ground.

3. Lock the jam nut (A) against the ball joint when neutral is

achieved.

4. Pull the ground speed control lever rearward and release

to check position again. Adjust as necessary to align
the ground speed control levers with the notches in the
neutral lock plate.

NOTE: This adjustment should not be performed
while the machine is running.

Not

for

Reproduction

«
...
30
31
32
33
34
...
»

Содержание 400ZB2548

















































Отзывы:

Нет отзывов

Похожие инструкции для 400ZB2548

Бренд: MTD Страницы: 16

Бренд: Viking Страницы: 56

Бренд: MTD Страницы: 12

Pro 12 DFS 37621231

Бренд: Peco Страницы: 32

Бренд: Flymo Страницы: 11

Z Master Professional 7500-D Series

Бренд: Toro Страницы: 80

Commercial Front Cut Rider YHRLD211

Бренд: Yazoo Страницы: 26

Бренд: RHINO Страницы: 23

Бренд: Gardeo Страницы: 128

Бренд: Husqvarna Страницы: 88

Бренд: Shindaiwa Страницы: 28

Бренд: Texas Equipment Страницы: 80

Бренд: Simplicity Страницы: 12

Бренд: Simplicity Страницы: 12

Бренд: Exmark Страницы: 56

Бренд: EINHELL Страницы: 208

Бренд: MTD Страницы: 20

Бренд: MTD Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды