Snapper 400ZB2548 Скачать руководство пользователя | Manualshive

Страница: 18 / 48

background image

16

www.SnapperPro.com

Starting the Engine

1. While sitting in the operator’s seat, engage the parking

brake by pulling the parking brake lever up, make sure
the PTO switch is disengaged (pressed down fully)
and the ground speed control levers are locked in the
NEUTRAL position.

2.

NOTE: A warm engine may not require
choking.

Set the engine throttle control to FULL throttle position.

Then fully close the choke by pulling the knob OUT fully.

3. Insert the key into the ignition switch and turn it to

START.

4. After the engine starts, gradually open the choke (push

knob down fully). Reduce to half throttle speed and
allow to warm up.

Warm up the engine by running it for at least a minute
before engaging the PTO switch or driving the rider.

5.

After warming the engine, ALWAYS operate
the unit at FULL THROTTLE when mowing.

In the event of an emergency the engine can be
stopped by simply turning the ignition switch
to STOP.

Use this method only in emergency

situations. For normal engine shut down follow the
procedure given in STOPPING THE RIDER.

Stopping the Rider

1. Returning the ground speed control levers to the middle

position will stop rider movement. Pivot the levers
outward and lock them in NEUTRAL.

2. Disengage the PTO by pushing down on the PTO switch.

3. Engage the parking brake by pulling the handle up until

it locks into position.

4. Move the throttle control to mid-throttle position and

turn the ignition key to OFF. Remove the key.

WARNING

If you do not understand how a specific control
functions, or have not yet thoroughly read the
FEATURES & CONTROLS section, do so now.

Do NOT attempt to operate the tractor without
first becoming familiar with the location and
function of ALL controls.

Pushing the Rider By Hand

1. Disengage the PTO, engage the parking brake, turn the

ignition OFF, and remove the key.

2. Locate the transmission release levers (A, Figure 8)

located underneath the front of the fuel tanks.

3. Pull both transmission release levers back and down so

that they lock in the disengaged (free-wheel position)
(C).

4. Disengage the parking brake.

The tractor can now be pushed by hand.

5. After moving the tractor, re-engage the transmissions by

pulling the transmission release levers up and pushing
them forward to the engaged (drive) position (B).

Figure 8. Transmission Release Levers (LH shown)
A. Transmission Release Lever
B. Engaged Position (Drive Position)
C. Disengaged Position (Free-wheel Position)

NOTICE

DO NOT TOW RIDER

Towing the units will cause transmission
damage. Do not use another vehicle to push or
pull this unit.

Operation

A

B

C

Not

for

Reproduction

«
...
16
17
18
19
20
...
»

Содержание 400ZB2548

















































Отзывы:

Нет отзывов

Похожие инструкции для 400ZB2548

Бренд: Gardol Страницы: 171

Бренд: Yard-Man Страницы: 11

Бренд: Troy-Bilt Страницы: 24

Бренд: EarthWise Страницы: 9

Бренд: Woods Страницы: 76

Бренд: Gardenline Страницы: 24

Бренд: MASCOT Страницы: 8

Бренд: Ryobi Страницы: 272

Бренд: Snapper Страницы: 52

Бренд: Spear & Jackson Страницы: 16

Бренд: MASSEY FERGUSON Страницы: 31

Бренд: Simplicity Страницы: 56

Бренд: Hayter Страницы: 36

Бренд: Cub Cadet Страницы: 44

Бренд: Craftsman Страницы: 32

Бренд: Craftsman Страницы: 52

Бренд: Craftsman Страницы: 36

Бренд: Craftsman Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды