Snapper 216517B, 2167517BV, R215517HC, Скачать руководство пользователя | Manualshive

Страница: 9 / 32

background image

9

Section 2 - OPERATING INSTRUCTIONS

WARNING

DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
HOT. Avoid serious burns, allow sufficient time for all
components to cool.

2.6 RECYCLING

OPERATION

NOTE: For best recycling results, cut up to a maximum of 1/3
of grass blade length and recycle ONLY when grass is dry.

1.  Set all wheels in the highest cutting position (Notch 6).
2.  Move engine speed control to “FAST” (Rabbit)
position.
3.  Move ground speed control to slowest speed setting.
4.  Proceed mowing slowly. If grass is very dense, lower
each rear wheel latch one notch lower than the front
wheel latches to improve recycling performance.

2.7 INSTALLATION of GRASS BAG ADAPTER
STEP 1: Install the grass bag adapter and secure to the
side and top of the deck with the two nuts provided on the
machine. Slot in front edge of adapter must be under nut
located on top of deck. See Figure 2.11.

FIGURE 2.11

2.8 INSTALLATION of RECYCLING PLUG
(Optional Accessory on Some Models)
STEP 1: Once adapter has been installed, recycling may
be desired. Insert recycling plug completely and securely
into adapter. Install grass bag. See Figure 2.12.

FIGURE 2.12

2.9 INSTALLATION of GRASS BAG

(Door Type Bag)
Install grass bag by sliding connector over flange of
adapter. See Figure 2.13.

FIGURE 2.13

(Continued on Next Page)

POSITION BAG
BETWEEN HANDLES

SLIDE
CONNECTOR
DOWN OVER BAG
ADAPTER FLANGE

BAG
ADAPTER

CONNECTOR

SECURE ADAPTER
TO DECK WITH NUTS

SECURE
WITH NUTS

ADAPTER

INSERT RECYCLING PLUG
COMPLETELY AND SECURELY
INTO ADAPTER. INSTALL
GRASS BAG.

ADAPTER

PLUG

«
...
7
8
9
10
11
...
»

Содержание 216517B, 2167517BV, R215517HC,

































Отзывы:

Нет отзывов

Похожие инструкции для 216517B, 2167517BV, R215517HC,

Бренд: Kärcher Страницы: 444

Бренд: AL-KO Страницы: 116

Бренд: Gardenline Страницы: 30

Бренд: Ryobi Страницы: 8

Бренд: Qualcast Страницы: 20

Бренд: Ryobi Страницы: 16

Бренд: Ransomes Страницы: 92

Бренд: Ransomes Страницы: 81

Бренд: Toro Страницы: 80

Derby Stallion ZT2561

Бренд: Simplicity Страницы: 39

RANSOMES 933304J

Бренд: Textron Страницы: 28

Бренд: Sabo Страницы: 100

Бренд: Troy-Bilt Страницы: 48

Бренд: SaMASZ Страницы: 41

Бренд: P.Lindberg Страницы: 123

Бренд: White Outdoor Страницы: 36

STANDER X 79490219

Бренд: WRIGHT Страницы: 24

Бренд: Dolmar Страницы: 204

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды