Snapper 216517B, 2167517BV, R215517HC, Скачать руководство пользователя | Manualshive

Страница: 18 / 32

background image

18

Section 4 - REPAIR & ADJUSTMENTS

WARNING

DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
HOT. Avoid serious burns, allow sufficient time for
all components to cool.

4.3.4. Replacing Rubber Driven Disc

(Continued from previous page)

2. Using needle nose pliers, unhook the drive
spring and slide the driven disc assembly off the
hex shaft. See Figure 4.12.
3.  Remove the two snap rings which secure the
rubber driven disc to the driven disc assembly.  See
Figure 4.13.
4.  Install new rubber driven disc onto driven disc
assembly with retaining rings.
5.  Reverse above procedures for reassembly and
installation of driven disc assembly.

FIGURE 4.12

4.3.5. Replacing Bearing In Driven Disc Assembly

IMPORTANT: The bearing on these machines is staked
into the thrust plate. The bearing will have to be driven
out with a mallet and a large punch. A new bearing with
four retaining screws will have to be purchased to
replace existing bearing.

If the driven disc bearing requires replacement,
remove the driven disc assembly and replace
bearing as follows:
1.  Using a small flat blade screwdriver, free the clip
from the transfer rod. Then remove the transfer rod
from the clip and the speed control rod. See Figure
4.11.
2. Using needle nose pliers, unhook the drive
spring and slide the driven disc assembly off the
hex shaft. See Figure 4.12.
3.  Remove both snap rings that secure rubber
driven disc hub to thrust plate. See Figure 4.13.
4.  Slide the rubber driven disc hub out of the
bearing.
5.  Drive out existing bearing.
6.  Install new bearing and secure to thrust plate
with four retaining screws. Tighten screws securely.
7.  Reassemble components in reverse order.

FIGURE 4.13

DRIVE DISC
ASSEMBLY

INSTALL NEW
DRIVEN DISC

SNAP
RINGS

«
...
16
17
18
19
20
...
»

Содержание 216517B, 2167517BV, R215517HC,

































Отзывы:

Нет отзывов

Похожие инструкции для 216517B, 2167517BV, R215517HC,

Бренд: McCulloch Страницы: 36

Бренд: Yard-Man Страницы: 16

Бренд: Sabo Страницы: 244

Бренд: SANLI Страницы: 16

Бренд: Weed Eater Страницы: 48

Бренд: RHINO Страницы: 98

HR 4600 Turbo 67862

Бренд: Jacobsen Страницы: 224

Бренд: Hyundai Страницы: 46

Smart Speed 569

Бренд: Troy-Bilt Страницы: 20

Four Wheel Steer Lawn Tractors

Бренд: Yard Machines Страницы: 16

Бренд: Dolmar Страницы: 76

Бренд: Craftsman Страницы: 56

Бренд: Baroness Страницы: 86

Бренд: EINHELL Страницы: 17

Бренд: GMC Страницы: 16

Бренд: Toro Страницы: 8

Бренд: Kärcher Страницы: 21

Бренд: ST. SpA Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды