Snapper 216517B, 2167517BV, R215517HC, Скачать руководство пользователя | Manualshive

Страница: 17 / 32

background image

17

Section 4 - REPAIR & ADJUSTMENTS

WARNING

DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
HOT. Avoid serious burns, allow sufficient time for
all components to cool.

4.3.3. DRIVEN DISC ADJUSTMENT

(Continued From Previous Page)

2. Remove driven disc spring from driven disc
assembly. Loosen connector hex nut. See Figure 4.9.

FIGURE 4.9

3. Slide driven disc assembly over to 1/8” from outside
edge of drive disc. Maintaining the 1/8” measurement,
remove any looseness from the linkage. This can be
done by holding the transfer rod and applying pressure
to the left (as viewed from operators position). Then
retighten the connector hex nut securely. See Figure
4.10. Move ground speed control to the first speed
position, then back to the sixth speed position.
Recheck the 1/8” measurement described previously.
Reinstall driven disc spring to driven disc assembly.

4.3.4. Replacing Rubber Driven Disc
If the rubber is badly chunked or worn it must be
replaced. Install new Driven Disc as follows:
1. Using a small flat blade screwdriver, free the clip
from the transfer rod. Then remove the transfer rod
from the clip and the speed control rod. See Figure
4.11.

FIGURE 4.10

FIGURE 4.11

(Continued On Next Page)

DRIVEN DISC
ASSEMBLY

DRIVE
DISC

DRIVEN DISC
SPRING

TRANSFER
ROD

CONNECTOR

CONNECTOR
HEX NUT

CONNECTOR
CLIP

SPEED
CONTROL
ROD

TRANSFER
ROD

SPEED
CONTROL
ROD

TRANSFER
ROD

CONNECTOR
CLIP

REINSTALLED CLIP
AND TRANSFER ROD

1/8” MEASUREMENT TO
OUTSIDE EDGE OF DRIVE
DISC

DRIVE
DISC

SLIDE DRIVEN
DISC ASSEMBLY
TOWARD OUTSIDE
EDGE

TRANSFER
ROD

CONNECTOR

CONNECTOR
HEX NUT

OUTSIDE
EDGE

«
...
15
16
17
18
19
...
»

Содержание 216517B, 2167517BV, R215517HC,

































Отзывы:

Нет отзывов

Похожие инструкции для 216517B, 2167517BV, R215517HC,

Бренд: ECLOZ Страницы: 60

44 968999551, 50 968999552, 44

Бренд: Dixon Страницы: 88

Бренд: Rally Страницы: 68

Swift S2 MJ71-190

Бренд: Major Страницы: 54

Бренд: Villager Страницы: 128

Бренд: Yazoo/Kees Страницы: 24

Бренд: Gardenline Страницы: 24

Бренд: Yard-Man Страницы: 42

Бренд: Simplicity Страницы: 14

Бренд: Gardenline Страницы: 24

Бренд: Land Pride Страницы: 34

Бренд: Scag Power Equipment Страницы: 96

Бренд: Royal Страницы: 64

Бренд: Sabo Страницы: 99

Бренд: Sabo Страницы: 114

Бренд: GGP Sweden Страницы: 52

Бренд: GGP ITALY Страницы: 58

Бренд: Craftsman Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды