background image

6 of 18 

3. CONTENTS 

 

The complete Desperado lift is contained in two (2) packages: 
1. The 

main structural components

 are packed on a shipping skid. 

2.  The remaining parts are packed in an 

accessory box

 

Main Structural Components include: 

1pc. 

Deck-Scissor Assembly (including Pull-Out Pan and Approach Ramp)

 

 
Accessory Box Contents: 

1pc. 

Power Pack Stand (with Power Pack) 

1pc. 

“Posi-Grip” Wheel Locator

  

1pc. 

12' Hydraulic Hose

 

1pc. Owner's 

Manual 

2pc. 

Wedge Anchor, ½”DIA x 4 ½”LG. (c/w nuts and washers) 

2pc. 

Carriage Bolt, ½”DIA x 5”LG. 

4pc. 

Hex Nut, ½”DIA 

 
 
 

4.  INSTALLATION REQUIREMENTS AND TOOLS 

 
NOTE: Lifts should only be installed on “level” concrete floors, with a minimum 
thickness of five (5) inches or 130mm.  Concrete must have a minimum strength of 
4000psi or 30 MPa and should be aged thirty (30) days prior to installation.  Please 
consult the architect, contractor or engineer if doubt exists as to the strength and 
feasibility of the floor to enable proper lift installation and operation 
 
Tools Required: 
 

1. 1/2” 

wrench 

2. 9/16” 

wrench 

3. 3/4” 

wrench 

4. 5/16” 

wrench 

5.  Rotary Hammer Drill 
6.  ½” Diameter Masonry Drill Bit 

Содержание DESPERADO EELR319A



















Отзывы: