background image

3 of 18 

1.  SAFETY AND OPERATING INSTRUCTIONS 

 

1.  Read all safety and operating instructions before using the lift. 
 
2.  Inspect the lift daily.  Do not operate the lift if it is damaged, malfunctioning, or if 

problems have been encountered. 

 
3.  Never attempt to overload the lift.  The manufacturer’s rated capacity is shown on the 

serial number tag, located on the scissor assembly. 

 
4. 

DO NOT OVERIDE

 the automatic safety devices incorporated into the lift. 

 
5.  Only trained and authorized personnel should operate the lift.  Do not allow 

customers or bystanders to operate the lift or be in the lift area.  Operators and 
bystanders must stay completely clear of the lift when raising and lowering. 

 
6.  The lift must only be operated on level and smooth floors. 
 
7.  Never drive a vehicle into position on the lift.  All vehicles must be pushed onto the 

lift.  Before rolling a vehicle on or off the lift, make certain that the lift has been 
completely lowered. 

 
NOTE:

 When positioning a vehicle on the lift, take time to center the load front-to-

 

rear and side-to-side.  The removal or installation of some vehicle parts may 

 

cause a critical shift in the center of gravity and may cause the vehicle to 

 become 

unstable. 

 
8. 

All vehicles must be securely fastened to the lift using tie down straps. 

 An 

appropriate tie down kit is available through SNAP-ON dealers (EELR319ATDK). 

 
9.  To raise the lift, press the “UP” button on the front face of the powerpack motor.  To 

lower, raise the lift until the automatic safety release device trips, then press down on 
the control lever. 

 
10. Do all work while the lift is on its mechanical safety lock. 
 
11. Always keep the lift area free of obstruction and debris.  Grease and oil spills should 

always be cleaned up immediately. 

 
12. Never raise the lift with a passenger onboard.  Do not climb onto the lift or vehicle 

when it is in the raised position. 

 
13. Retract the approach ramp after the lift has been raised to avoid any sharp, protruding 

objects. 

 
14. Avoid excessive rocking of the lift while it is in the raised position. 
 
15. Before lowering the lift, check the area for obstructions. 

Содержание DESPERADO EELR319A



















Отзывы: