Snap-on Incorporated EEWB314A Скачать руководство пользователя страница 36

Страница: 36 / 38

Page 3-18

CHAPTER 3 CHECKOUT, CALIBRATION AND MAINTENANCE

Effective

09/2005

Screw

10 Pin
connector

Spacers /
Bolts

Figure 3-35

FIGURE 3-36

VIBRATORY MEMBER REMOVAL

• Disconnect the power from the rear of the

machine.

• Remove the Display panel.
• Remove the weight tray.
• Remove the rear transducer.
• Using 1/4” drive 6mm hex head SOT part #

TMAM6E remove the six (6mm) hex bolts to the
vibratory. Pay special attention of spacer
placement. (Figure 3-35)

• Lift up on the vibratory member and remove.

VIBRATORY INSTALLATION

• Lift and set vibratory member into the balancer

housing.

• Insert spacers.
• Apply Loctite® to the hex bolts.
• With the aid of a helper start the two lower hex

bolts.

• Install the 4 remaining hex bolts and tighten to

22ft. lbs. +/- 3 in. lbs.

• Install the rear transducer and follow transducer

installation.

• Install weight tray.
• Install control panel assmebly.
• Connect power and follow all calibration proce-

dures

P83, P84

and test.

NOTE: THE SERVICE TECHNICIAN MUST USE

THE PRUEFROTOR AFTER THE
INSTALLATION OF A VIBRATORY
MEMBER IN ORDER TO ENSURE ISO
9000 STANDARDS.

ENCODER REMOVAL

(Figure 3-36)

• Disconnect power.
• Remove Main PCB.
• Remove weight tray.
• Disconnect the 10 Pin ribbon cable from the

encoder PCB.

• Remove the phillip screw holding the encoder

pcb to the shaft tube.

NOTE: BE CAREFUL NOT TO LET FOREIGN

DEBRIS FALL INSIDE THE TUBE.

Содержание EEWB314A






































Результаты поиска

Содержание EEWB314A

Отзывы:

Бренды по названию

Популярные бренды

Snap-on Incorporated EEWB314A, Руководство по обслуживанию

Результаты поиска

Содержание EEWB314A

Отзывы:

Бренды по названию

Популярные бренды