Snap-on Incorporated EEWB314A Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 38

Snap-on Incorporated EEWB314A Скачать руководство пользователя страница 35

Page 3-17

CHAPTER 3 CHECKOUT, CALIBRATION AND MAINTENANCE

Effective
09/2005

VOLTAGE REGULATOR

The balancer can operate using AC power or using the
Snap-on Versavolt battery pack used to power Snap-
on power tools. The balancer will accomodate either
the 12V, 14.4V or 18V battery pack. The voltage
regulator is designed to keep the incoming power from
the battery regulated to 12VDC. Should a battery
require charging the balancer can quickly be switched
from battery voltage to shop power with the flip of a
switch.

To replace the Voltage Regulator the SAPE assembly
and bottom tray must be removed to allow access to
the screws securing the voltage regulator.

POWER SWITCH

The switch used on the balancer is a double throw
switch. To switch the power off the switch must be set
in the middle position.

Red Arrow - battery input
Blue Arrow - To Processor PCB
Green Arrow - Incoming power

Figure 3-32

Figure 3-33

Figure 3-34

«
...
33
34
35
36
37
...
»

Содержание EEWB314A







































Отзывы:

Нет отзывов