manualshive.com logo in svg

SMSC LAN9312, Техническое описание


Поделиться
Скачать
background image

High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface

Datasheet

Revision 1.4 (08-19-08)

28

SMSC LAN9312

DATASHEET

 

3.2

  Pin Descriptions

This section contains the descriptions of the LAN9312 pins. The pin descriptions have been broken
into functional groups as follows:

„

LAN Port 1 Pins

„

LAN Port 2 Pins

„

LAN Port 1 & 2 Power and Common Pins

„

Host Bus Interface Pins

„

EEPROM Pins

„

Dedicated Configuration Strap Pins

„

Miscellaneous Pins

„

PLL Pins

„

Core and I/O Power and Ground Pins

„

No-Connect Pins

Note:

A list of buffer type definitions is provided in 

Section 1.2, "Buffer Types," on page 18

.

Table 3.1  LAN Port 1 Pins

PIN

NAME

SYMBOL

BUFFER 

TYPE

DESCRIPTION

89-92

Port 1 LED 

Indicators

nP1LED[3:0]

OD12

LED Indicators: 

When configured as LED outputs 

via the 

LED Configuration Register (LED_CFG)

, 

these pins are open-drain, active low outputs and 
the pull-ups and input buffers are disabled. The 
functionality of each pin is determined via the 
LED_CFG[9:8] bits.

General 

Purpose I/O 

Data

GPIO[3:0]

IS/O12/

OD12

(PU)

General Purpose I/O Data:

 When configured as 

GPIO via the 

LED Configuration Register 

(LED_CFG)

, these general purpose signals are 

fully programmable as either push-pull outputs, 
open-drain outputs or Schmitt-triggered inputs by 
writing the 

General Purpose I/O Configuration 

Register (GPIO_CFG)

 and 

General Purpose I/O 

Data & Direction Register (GPIO_DATA_DIR)

. The 

pull-ups are enabled in GPIO mode. The input 
buffers are disabled when set as an output.

Note:

See 

Chapter 13, "GPIO/LED Controller," 

on page 162

 for additional details.

110

Port 1 

Ethernet TX 

Negative

TXN1

AIO

Ethernet TX Negative: 

Negative output of Port 1 

Ethernet transmitter. See 

Note 3.1

 for additional 

information.

111

Port 1 

Ethernet TX 

Positive

TXP1

AIO

Ethernet TX Positive: 

Positive output of Port 1 

Ethernet transmitter. See 

Note 3.1

 for additional 

information.

115

Port 1 

Ethernet RX 

Negative

RXN1

AIO

Ethernet RX Negative: 

Negative input of Port 1 

Ethernet receiver. See 

Note 3.1

 for additional 

information.

116

Port 1 

Ethernet RX 

Positive

RXP1

AIO

Ethernet RX Positive: 

Positive input of Port 1 

Ethernet receiver. See 

Note 3.1

 for additional 

information.

Содержание LAN9312











































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LAN9312

Cabletron Systems SmartSwitch 9A100 Installation And Setup Manual preview
SmartSwitch 9A100
Бренд: Cabletron Systems Страницы: 52
Cabletron Systems SmartSwitch 9W006 Quick Start Manual preview
SmartSwitch 9W006
Бренд: Cabletron Systems Страницы: 34
Cabletron Systems SmartSTACK ELS100-S24TX2M Management Manual preview
SmartSTACK ELS100-S24TX2M
Бренд: Cabletron Systems Страницы: 102
Cabletron Systems 9A426-01 Appendix preview
9A426-01
Бренд: Cabletron Systems Страницы: 24
Cabletron Systems SmartSwitch 9000 Appendix preview
SmartSwitch 9000
Бренд: Cabletron Systems Страницы: 14
Cabletron Systems MicroMMAC 22ES Reference Manual preview
MicroMMAC 22ES
Бренд: Cabletron Systems Страницы: 38
Campbell Hausfeld CW301300AJ Operating Instructions And Parts Manual preview
CW301300AJ
Бренд: Campbell Hausfeld Страницы: 12
K-Dyne OMP L80-P Manual preview
OMP L80-P
Бренд: K-Dyne Страницы: 10
Inline MSV0502 Operation Manual preview
MSV0502
Бренд: Inline Страницы: 26
IOGear MicroHub GUH274W3 (Portuguese) Manual Do Usuário preview
MicroHub GUH274W3
Бренд: IOGear Страницы: 1
Pilz PSEN 1.2p-25 Operating Instructions Manual preview
PSEN 1.2p-25
Бренд: Pilz Страницы: 8
N-Tron 716M12 User Manual & Installation Manual preview
716M12
Бренд: N-Tron Страницы: 169
GarrettCom Magnum CS14 Series Installation And User Manual preview
Magnum CS14 Series
Бренд: GarrettCom Страницы: 76
AbleNet 100DSLAT Quick Start Manual preview
100DSLAT
Бренд: AbleNet Страницы: 6
Clas Ohlson EMT1700P Manual preview
EMT1700P
Бренд: Clas Ohlson Страницы: 5
Ross OpenGear DSS-8224 User Manual preview
OpenGear DSS-8224
Бренд: Ross Страницы: 47
Quidway S5012G-DC Installation Manual preview
S5012G-DC
Бренд: Quidway Страницы: 43
Xantech 686-10 Installation Instructions preview
686-10
Бренд: Xantech Страницы: 5

Бренды по названию

Популярные бренды

Загрузить еще бренды