Smith-Root ELECTROFISHING BOATS Скачать руководство пользователя

Страница: 22 / 53

2007

ELECTROfISHING

BOATS

OUTBOARD

1. Disconnect or shut off fuel.
2. Run engine to eliminate fuel from carburetors (until

engine quits).

Note:

Do not run engine without water; use hose adapter

recommended by outboard manufacturer.

Note:

Do not run engine tilted up.

3. Remove spark plugs.

4.  Spray fogging oil in each cylinder.
5.  Cycle the engine (manually or electrically).
6.  Spray each cylinder again and replace the spark plugs.

Note:

Do not connect plug wires.

7. Spray fogging oil into carburetor air intakes.
8. Cycle the engine (manually or electrically).

9. Replace plug wires.

10. Replace engine shroud.
11. Store boat with outboard tilted down, if possible.
12. Check owner's manual for additional advice.

GENERATOR

1. Leave fuel valves turned off. Start engine to drain carburetor

bowl.

2. Remove spark plug and spray fogging oil into cylinders.

3. Cycle engine (manually or electrically).
4. Spray cylinders again and replace spark plugs.

Do not reconnect plug wires.

5.  Cycle engine again.
6.  Now replace the plug wires.
7.  Change the oil and filter:

a. Connect hose to 3/8" pipe fitting marked "Oil Drain"

located behind Generator Housing.

b. Route Oil Drain Hose through Stern Drain in

Transom.

8. Open Winterizing Drain Valve (behind Gen. Housing) to

drain raw water from Generator.

9. Drain the water from the generator cooling hose by

removing the cap from the "T" fitting located inside the

generator compartment, below the compartment light.

Replace the cap and tighten by hand.

10. Drain water strainer located on side of console.
11. Open cover from generator water pump and lubricate

impeller with silicone grease.

BATTERIES

Connect Automatic Battery Charger with maintenance

float feature to the connector labeled "Battery Charger"

on the Console.

fUEL SYSTEM

1. When you fill up the onboard fuel tanks for the last trip

of the year, add a fuel stabilizer to it.

2. After returning from the last field trip, top off the fuel

tanks with fuel and conditioner.

3. With fuel shut-off valves turned off, remove and discard

the old fuel filter.

4.  Install a new fuel filter per manufacturer's instructions.
5.  Do not re-prime the fuel filter at this time.
6.  Leave fuel shut-off valves turned off.
7.

Note:

Leaving your fuel tanks full will minimize

condensation build-up inside the fuel tank.

fISH TANK DRAINING

1. Locate Livewell Winterizing Drain valve. Open valves to

drain any water into bilge.

WINTERIzATION

Содержание ELECTROFISHING BOATS






















































Результаты поиска

Содержание ELECTROFISHING BOATS

Отзывы:

Похожие инструкции для ELECTROFISHING BOATS

Бренды по названию

Популярные бренды

Smith-Root ELECTROFISHING BOATS, Руководство пользователя

Результаты поиска

Содержание ELECTROFISHING BOATS

Отзывы:

Похожие инструкции для ELECTROFISHING BOATS

Бренды по названию

Популярные бренды