SMC Networks PFG3 0 Series Скачать руководство пользователя страница 73

Страница: 73 / 85

-72-

No.PF

※※

-OMU0007-B

Problem

No.

Problem

Possible cause

Investigation method

Countermeasures

•Over current

error (Er1,2) is
displayed.

•COPY receiving

error (Er13) is
displayed.

•System error

(Er0, 4, 6, 7, 8,
14,40) is
displayed.

•"HHH" is

displayed.

•"LLL" is

displayed.

Excess current
was applied to
the output (Er1,2)

(1) Check if the output current is 20

mA or more.

(2) Check if the connected load

complies with the specification.
Check if the load is short circuited.

(3) Check if the relay without surge

protection is connected.

(4) Check if the wiring is in the same

route as (or bundled together
with) a high-voltage or power line.

(1)(2) Connect the

appropriate load.

(3) Use a relay with a surge

voltage suppressor or
take measures to prevent
surge.

(4) Separate the wiring from

the high-voltage and/or
power line.

Copy function
operated
incorrectly (Er13)

Check the wiring.
Check if the brown and blue wires are
connected to DC(+) and DC(-)
respectively and the grey wires to
each monitor are connected, and that
the wiring is secure.

Correct the wiring.

Incorrect internal
data processing
of the product
(Er0,4,6,7,8,14,4
0)

(1) Check if there is noise

interference (such as static
electricity).

Check if there is a noise source
nearby.

(2) Check if the power supply voltage

is in the range 12 to 24 VDC
±10%.

(1) Remove the noise and

the noise source (or take
measures to prevent
noise interference), and
reset the product (or turn
off and then turn back on
the power supply.

(2) Supply power in the

range 12 to 24 VDC
±10%.

Applied flow is
higher than the
upper limit (HHH)

(1) Check if the flow exceeds the

upper limit of the set flow range.

(2) Check if foreign matter has

entered the piping.

(1) Reset applied flow to a

level within the set flow
range.

(2) Take measures to

prevent foreign matter
from entering the piping.

Applied flow is
lower than the
lower limit (LLL)

(1) Check if the flow exceeds the

lower limit of the set flow range.

(2) Check if foreign matter has

entered the piping.

(1) Reset applied flow to a

level within the set flow
range.

(2) Take measures to

prevent foreign matter
from entering the piping.

Product failure

Replace the product.

The display is
unstable.

Incorrect power
supply

Check if the power supply voltage is
in the range 12 to 24 VDC ±10%.

Supply power in the range
12 to 24 VDC ±10%.

Incorrect wiring

Check the power supply wiring.
Check if the brown and blue wires are
connected to DC(+) and DC(-)
respectively, and if the wiring is
secure.

Check and correct the
wiring.

Factory line
pressure is not
stable

Check if the factory line flow is stable.

Improve the display stability
by setting the delay time or
digital filter.

Содержание PFG3 0 Series






















































































Результаты поиска

Содержание PFG3 0 Series

Отзывы:

Бренды по названию

Популярные бренды

SMC Networks PFG3 0 Series, Руководство по эксплуатации

Результаты поиска

Содержание PFG3 0 Series

Отзывы:

Бренды по названию

Популярные бренды