manualshive.com logo in svg

SMC Networks PFG3 0 Series, Руководство по эксплуатации

Поделиться
Скачать
SMC Networks PFG3 0 Series Скачать руководство пользователя страница 45

 

-44- 

 

No.PF

※※

-OMU0007-B 

 

 

■

[F 5] FUNC terminal function setting 

Analogue output, external input or copy function can be selected. 

: Do not connect the grey wire when changing the setting. 

•When the analogue output is selected 

When the product with analogue voltage output is used, the output of 1 to 5 V or 0 to 10 V can be selected. 
A flow value corresponding to 5 V (10 V) or 20 mA can be selected with the analogue output free range 
function. 

 

•When the external input is selected 

The Accumulated Flow, Peak Value and Bottom Value can be reset remotely by an external input signal. 

•Accumulated flow external reset: A function to reset the accumulated flow value when an external input 

signal is applied. 

In accumulated increment mode, the accumulated flow value will reset 
to zero, and then increase from zero. 
In accumulated decrement mode, the accumulated flow value will reset 
to a set value, and then decrease from the set value. 

 

: When the Accumulated Value has been stored to memory, every time the Accumulated Value External Reset is activated, the 

memory will be accessed. Take into consideration the maximum number of times the memory can be accessed is1.5 million 

times. 

When using the product, it should be considered that the total number of external input resets and accumulated values stored 

must not exceed 1.5 million cycles. 

•Peak/Bottom value reset: A function to clear the peak value or bottom value in response to an external 

input signal. 

 

•When the copy function is selected 

The set value of the monitor master side can be copied. 

Содержание PFG3 0 Series






















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды