SMC Networks PFG3 0 Series Скачать руководство пользователя страница 16

Страница: 16 / 85

-15-

No.PF

※※

-OMU0007-B

Attaching the connector to the sensor wire

•Strip the sensor wire as shown.
•Do not cut the insulator.
•Insert the corresponding wire colour shown in the table into the

pin number printed on the sensor connector, to the bottom.

Pin no.

Wire colour



Description

Brown

DC(+)

Blue

DC(-)

White



: The wire colours shown are for the PFMB, PFMC, and PF3A7 series cables.

•Check that the above preparation has been performed correctly, then part A shown should be pressed in by

hand to make temporary connection.

•Part A should then be pressed in using a suitable tool, such as pliers.

•The sensor connector cannot be re-used once it has been fully crimped.

In cases of connection failure such as incorrect order of wires or incomplete insertion, please use a new
connector.

•If the sensor is not connected correctly "LLL" or "HHH" will be displayed.

Содержание PFG3 0 Series






















































































Результаты поиска

Содержание PFG3 0 Series

Отзывы:

Похожие инструкции для PFG3 0 Series

Бренды по названию

Популярные бренды

SMC Networks PFG3 0 Series, Руководство по эксплуатации

Результаты поиска

Содержание PFG3 0 Series

Отзывы:

Похожие инструкции для PFG3 0 Series

Бренды по названию

Популярные бренды