Z_ISE40A-TF2Z052EN
Page 3 of 3
11 Error Indication
12 Maintenance
12.1 General Maintenance
Caution
•
Not following proper maintenance procedures could cause the product
to malfunction and lead to equipment damage.
•
If handled improperly, compressed air can be dangerous.
•
Maintenance of pneumatic systems should be performed only by
qualified personnel.
•
Before performing maintenance, turn off the power supply and be sure
to cut off the supply pressure. Confirm that the air is released to
atmosphere.
•
After installation and maintenance, apply operating pressure and
power to the equipment and perform appropriate functional and
leakage tests to make sure the equipment is installed correctly.
•
If any electrical connections are disturbed during maintenance, ensure
they are reconnected correctly and safety checks are carried out as
required to ensure continued compliance with applicable national
regulations.
•
Do not make any modification to the product.
•
Do not disassemble the product, unless required by installation or
maintenance instructions.
How to reset the product after a power cut or forcible de-energizing
The setting of the product will be retained as it was before a power cut or
de-energizing.
The output condition is also basically recovered to that before a power
cut or de-energizing but may change depending on the operating
environment.
Therefore, check the safety of the whole installation before operating the
product.
If the installation is using accurate control, wait until the product has
warmed up (approximately 10 to 15 minutes).
13 Limitations of Use
13.1 Limited warranty and Disclaimer/Compliance Requirements
Refer to Handling Precautions for SMC Products.
Caution
•
SMC products are not intended for use as instruments for legal
metrology.
Measurement instruments that SMC manufactures or sells have not
been qualified by type approval tests relevant to the metrology
(measurement) laws of each country.
Therefore, SMC products cannot be used for business or certification
ordained by the metrology (measurement) laws of each country.
14 Product Disposal
This product shall not be disposed of as municipal waste. Check your
local regulations and guidelines to dispose of this product correctly, in
order to reduce the impact on human health and the environment.
15 Contacts
Refer to
www.smcworld.com
or
www.smc.eu
for your local distributor /
importer.
URL:
https://www.smcworld.com
(Global)
https://www.smc.eu
(Europe)
SMC Corporation, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, Japan
Specifications are subject to change without prior notice from the manufacturer.
© 2021 SMC Corporation All Rights Reserved.
Template DKP50047-F-085M
Error Name
Error
Display
Error Type
Troubleshooting
Method
Over
current
Error
The switch
output load
current is more
than 80 mA.
Turn the power off
and remove the
cause of the over
current. Then turn
the power on.
Residual
Pressure
Error
During zero
clear operation,
pressure above
±7% F.S.
(±3.5% F.S. for
compound
pressure) has
been applied.
After 1 second,
the mode will
return to
measurement
mode. The zero
clear range can
vary ±1% F.S.
with individual
product
differences.
Perform zero clear
operation again
after restoring the
applied pressure to
an atmospheric
pressure condition.
Pressurizing
Error
Pressure has
exceeded the
upper limit of the
set pressure
range.
Adjust the applied
pressure to a level
within the set
pressure range.
Pressure has
exceeded the
lower limit of the
set pressure
range.
Auto-shift
error
The measured
pressure at
auto-shift input
exceeds the set
pressure range.
*: After 1 s,
measurement
mode returns
automatically.
Auto-shift input is
invalid.
Check the
connected
equipment and
machine.
System
Error
Displayed in the
case of an
internal data
error.
Turn the power off
and turn it on
again.
If resetting fails, an
investigation by
SMC Corporation
will be required.
If the error cannot be reset after the above measures are taken, contact
SMC.
