SMC Corporation LECSA series Скачать руководство пользователя

Страница: 365 / 419

13 - 57

13. POSITIONING MODE

13.6.4 Count type home position return
In count type home position return, a motion is made over the distance set in parameter No. PE09 (moving

distance after proximity dog) after detection of the proximity dog front end. The position where the first Z-phase

signal is given after that is defined as a home position. Hence, if the proximity dog (DOG) is 10ms or longer,

there is no restriction on the dog length. This home position return method is used when the required proximity

dog length cannot be reserved to use dog type home position return or when the proximity dog (DOG) is

entered electrically from a PC or PLC...etc or the like.

(1) Devices and parameters

Set the input devices and parameters as follows.

Item

Device/Parameter used

Description

Manual home position return

mode selection

Automatic/manual selection (MD0)

Turn MD0 ON.

Point table No./Program No.

selection 1 to 3 (DI0 to DI2)

Point table method: Select the home position return

mode by turning OFF DI0, DI1 and

DI2.

Program method: Select a program that has the home

position return "ZRT" command.

Count type home position return Parameter No. PE03

1: Count type home position return is selected.

Home position return direction

Parameter No. PE03

Refer to section 13.6.1 (2) and select the home position

return direction.

Dog input polarity

Parameter No. PE03

Refer to section 13.6.1 (2) and select the dog input

polarity.

Home position return speed

Parameter No. PE04

Set the speed till the dog is detected.

Creep speed

Parameter No. PE05

Set the speed after the dog is detected.

Home position shift distance

Parameter No. PE06

Set when shifting the home position, starting at the first

Z-phase signal given after passage of the proximity dog

front end and movement over the travel distance.

Travel distance after proximity

dog

Parameter No. PE09

Set the travel distance after passage of proximity dog

front end.

Home position return

acceleration/deceleration time

constants

Parameter No. PE07

Set the acceleration/deceleration time constants during

a home position return.

Home position return position

data

Parameter No. PE08

Set the current position at home position return

completion.

Содержание LECSA series




































































































































































































































































































































































































































Результаты поиска

Содержание LECSA series

Отзывы:

Похожие инструкции для LECSA series

Бренды по названию

Популярные бренды

SMC Corporation LECSA series, Руководство по эксплуатации

Результаты поиска

Содержание LECSA series

Отзывы:

Похожие инструкции для LECSA series

Бренды по названию

Популярные бренды