background image

 

 

ASSEMBLE FRONT PANEL

 

10

 

BOTTOM PLATE

 

1854mm

 

1854mm

 

TOP PLATE

 

SELECT:

 

 

3 x 1.890 Wall Sheets

 

1 x 2.520 Top Plate (Red)

 

1 x 2.520 Bottom Plate (Green)

 

2 x 1.890 Door Jamb Flashings

 

40 x 30mm Galv Clouts

 

19 x Rivets

 

STEP 1:

 

 

• 

Lay out 1 x Top Plate and 1 x Bottom Plate on a flat 
surface as shown 

 

STEP 2:

 

 

• 

Using 2 x 30mm clouts, nail the Door Jamb Flashing flush with 
the top of the Top Plate at the correct  measurement as shown 
in plan view. Pre drill holes using a 3.5mm drill bit

 

 

• 

Check the distance between the top and bottom plates then use 
a further 2 x 30mm clouts to nail the Door Jamb Flashings to 
the bottom Plate. Pre drill holes.

 

STEP 4:

 

 

• 

Place the door on the panel (In open position, approx 
20mm below top of top plate). Using two rivets, rivet the top 
and bottom hinges to the Door Jamb Flashing, ensuring 
door closes properly. 

 

 

• 

Fit remaining rivets.

 

STEP 3:

 

 

• 

Place 3 x Wall Sheets on timber.

 

 

• 

Ensure that the top of the sheets are flush with the top of the 
Top Plate and that the sides of the wall sheets overhang the 
Top Plate by 

15mm

 as shown. Nail wall sheets to Top Plate 

(two clouts per pan)

 

 

• 

Nail the wall sheets to the Bottom Plate making sure that the 
Plates are the correct distance apart and that the sides of the 
wall sheets overhang the Bottom Plate by 

15mm

.

 

 

• 

Drill & rivet Door Jamb Flashings to wall sheets using four 
rivets equally spaced on each side.

 

NOTE: 

The

 

Doorway is standard at 530mm from left

-

hand end. 

To shift the doorway to the right

-

hand side of the front 

wall, simply measure 530mm from the right

-

hand end.

 

NOTE: 

Door can be hinged on either side.

 

IMPORTANT—IF YOU CHOOSE TO RAISE YOUR TIMBER 

BASE PLATE –READ THE FOLLOWING;

 

 

For sheds with Raised Base Plate option only (see page 6), deduct 

30mm from measurement shown between Top and Bottom Plates on 
all wall panels, so cladding protrudes 20mm below bottom plate

.

 

TOP PLATE

 

TOP PLATE

 

15mm

 

15mm

 

15mm

 

15mm

 

530mm

 

960mm

 

TOP PLATE

 

DOOR OPENING

 

x3

 

x3

 

x3

 

Plan View

 

TOP

 

PLATE

 

DOOR

 

JAMB

 

NAIL

 

Содержание SM2520

















Отзывы: