background image

 

 

ASSEMBLE BACK PANEL

 

SELECT:

 

 

5 x 1.890 m Wall Sheets

 

1 x 2.520 m Top Plate (Red)

 

1 x 2.520 m Bottom Plate (Green)

 

60 x 30mm Galv Clouts

 

8 x Rivets

 

STEP 1:

 

 

• 

Lay out 1 x Top Plate and 1 x Bottom Plate on a 
flat surface as shown (corner cutouts to face in-
wards). 

 

STEP 2:

 

 

• 

Place 5 x 1.890 m wall sheets on top of timber 
Plates with bottom of sheets flush with each other. 

 

 

• 

Rivet the sheets together on overlaps as shown

.

 

STEP 3:

 

 

• 

Nail the wall sheets to the Top Plate at each end making sure 
that the top of the sheets are flush with the top of the Top 
Plate and that the sides of the wall sheets overhang the Top 
Plate by 

15mm

 as shown.

 

 

• 

Check that the Top Plate is straight then nail wall sheets to 
the Top Plate, using two clouts per pan. 

 

STEP 4:

 

 

• 

Nail the wall sheets to the Bottom Plate at each end, 

 

     ensuring that each side of the wall sheets overhangs the                           

Bottom Plate by 

15mm

 and that the distance between 

 

     the Top and Bottom Plates is correct. (As shown)

 

 

• 

Check that the Bottom Plate is straight then nail  

 

     wall sheets to the Bottom Plate, using two clouts per pan

.

 

9

 

BOTTOM PLATE

 

1854mm

 

1854mm

 

TOP PLATE

 

Standard Shed —

 

Bottom Plate will protrude below wall 

sheet by approximately 10mm. 

 

 

Raised base plate shed —

 

Wall sheet will protrude below 

the Bottom Plate by 20mm

.

 

IMPORTANT—IF YOU CHOOSE TO RAISE YOUR TIMBER 

BASE PLATE –READ THE FOLLOWING;

 

 

For sheds with Raised Base Plate option only (see page 6), deduct 

30mm from measurement shown between Top and Bottom Plates on 
all wall panels, so cladding protrudes 20mm below bottom plate

.

 

TOP PLATE

 

BOTTOM PLATE

 

TOP PLATE

 

15mm

 

15mm

 

1854mm

 

1854mm

 

BOTTOM PLATE

 

15mm

 

15mm

 

TOP PLATE

 

Содержание SM2520

















Отзывы: