background image

Appendix 1:System connection

      [

Seawater, A.T.O. source  is water purifier

HIG

MID

LOW

     A.T.O.
       

    A.W.C.
        

  Freq.

Smartreefs

AUTO WATER CHANGER

Buzzer

   Pause
  

***

HIG

MID

LOW

     A.T.O.
       

    A.W.C.
        

  Q

.

L.

Smartreefs

AUTO WATER CHANGER

A.P.

   Pause
       &     
      Set
  

8 8 8 8

    *The temperature probe must not be completely
      submerged in water, and the water level should
      be below the highest water level line marked on 
      the probe.

·  

 

The temperature probe is not hot-swappable.

Power
Supply

Controller

 

Water level indicator

Function
    keys

Digital display

Fish tank

Pipe
rack

Anti-siphon
device

Black connector

Green connector

Main control 
installation position

TEMP
Sensor

Sea water storage bucket

Sewer
or waste 
water tank

Anti-siphon
device

White connector

**

Physical safety device
         (Optional)

Dn8 solenoid valve
       (Optional)

Freshwater source

*

· 

This device can be used repeatedly, just need to replace the compression 

sponge.

Please install the water inlet and outlet pipes according to the direction 

of the water flow indicated by the arrow on the side of the solenoid valve. 
Incorrect installation of the water inlet and outlet pipes will cause the 
solenoid valve to fail to cut off the water channel.

** 

A physical safety device must be installed on the floor (lower ground) 

near the fish tank.

· 

Please place the compression sponge on the front of the safety device, in 

the circular area under the physical switch, and then press the physical 
switch.

· 

If the compression sponge comes into contact with a small amount of 

water, the switch above will be lifted by the expansion, and the water 
channel will be forced to be cut

.

Note: If the water pipe is too long or the water pipe needs to climb the wall, please purchase a high-lift 
pump and power extension cable from the dealer to achieve water in and out at a long distance.

Note 2: The solenoid valve and physical safety device in the picture are optional accessories. Please purchase 
it from the dealer to replace the water pump to realize automatic water exchange without bucket.

Содержание Tosta-PRO














Отзывы: