manualshive.com logo in svg

SmartPower HR-10, Руководство пользователя

Поделиться
Скачать
SmartPower HR-10 Скачать руководство пользователя страница 53

Smart Power Systems

®

 

A. C. MODULAR GENERATOR SYSTEM 

Page 52 of 56 

 

 

Pump Adjustment 

 

 

WARNING: 

 

The SPS Electronic Controlled Generators have been pre-set at the factory to provide 
correct frequency and voltage, no pump adjustments are required.  If it appears the 
pump need to be adjusted, contact SPS at (231) 832-5525 before proceeding.  Damage 
to the generator from improper pump adjustments will void the system’s warranty. 
 
To  prevent  permanent,  un-repairable  damage  to  the  generator,  never  adjust  the 
hydraulic pump so the generator’s output frequency exceeds 65 Hz. 
 
Make  adjustments  to  the  hydraulic  pump  flow  control  with  all  electrical  loads 
disconnected from generator. 
 
Never adjust the p

ump’s pressure control. 

 
 

Reasons for adjusting the pump: 

 
1. 

Generated output frequency is “too low.”  Verify output frequency when the vehicle is 
in fast idle and oil temperature is below 160

F.  If the frequency drops below 59Hz, 

the pump output flow may need to be increased. 

 
2. 

The hydraulic system is running excessively hot:  If the system’s oil temperature is 
running above 160

F with an ambient air temperature of 80

F, the pump output flow 

may  need  to  be  decreased.    Before  making  any  adjustment,  verify  the  system  is 
getting adequate ventilation, the fan is operating, the oil cooler air passageways are 
not plugged and the hot air exiting the cooler is not being drawn back through the 
cooler.  Operate system after correcting ventilation problems to validate whether the 
system still overheats prior to making pump adjustment. 

 

Note:

  

The generator’s output frequency cannot be decreased by adjusting the pump 

flow.  If the generator output frequency is too high, contact SPS at (231) 832-5525 
for further instructions. 

 
 

 

 

Содержание HR-10


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды