manualshive.com logo in svg

SmartPower HR-10, Руководство пользователя

Поделиться
Скачать
SmartPower HR-10 Скачать руководство пользователя страница 17

Smart Power Systems

®

 

A. C. MODULAR GENERATOR SYSTEM 

Page 16 of 56 

 

WARNING: 

 

Do not install hose ends until proper hose length has been determined. 
Ensure debris is kept out of the hoses and hydraulic system prior to installation. 
 
Never install a hose in a location where it will rub against another surface or abrasive 
member. 
 
Do  not  position  hoses  with  tight  bend  radii.  Consult  the  hose  manufacturer

’s 

installation  guidelines.    Tight  bends  may  kink  and  cause  serious  damage  to  the 
system and will void the system’s warranty. 
 
Use  caution  when  tightening  the  hose  ends  to  prevent  the  hose  from  becoming 
twisted. 
 
Never install a 90° fitting at the pump inlet or outlet.  Avoid the use of flow restricting 
fittings. 

 

Do not form loops in the hose that may collect air or kink.  Run hoses as straight as 
possible (but not taut) between connections.  
 
Do not exceed hose lengths of 20 feet. 

 

Smart Power has fully tested and approved ISO fluids 

ISO #32, #46 and #68 are approved for use in all Smart Power hydraulic generators. 
 
Complete testing was performed using U.S. Oil Multi-Vis R Hydraulic Fluid under 
controlled environments ranging from below freezing to above NFPA’s high temperature 
requirements. The systems ran within our tight performance specifications using all three 
listed grades. 
 
ISO #32 is recommended when ambient temperatures are generally between 2 and 56°F. 
ISO #46 is recommended when ambient temperatures are generally between 10 and 
74°F. 
ISO #68 is recommended when ambient temperatures are generally between 27 and 
95°F. 
For additional information on ISO fluids, contact U.S. Oils, or your local ISO grade fluid 
supplier. 
 
6. 

 SPS models HR-6.2, HR-8, HR-10 and HR-110 can be mounted on top of a vehicle, 
in  the  open,  without  requiring  any  additional  coverings.    Reference  Figure  3  and 
Figure  4  for  the  minimum  clearances  around  the  perimeter  of  the  generator  tray 
assembly.  Also, do not position any obstructions directly in front of the system’s oil 
cooler. If the system cannot be installed without maintaining the minimum clearances 
as indicated, or if you have any questions relative to the installation of these systems, 
contact Smart Power Systems

®

 at (231) 832-5525. 

  

Содержание HR-10


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды