manualshive.com logo in svg

SmartPower HR-10, Руководство пользователя

Поделиться
Скачать
SmartPower HR-10 Скачать руководство пользователя страница 4

Smart Power Systems

®

 

A. C. MODULAR GENERATOR SYSTEM 

Page 3 of 56 

 

Never operate the system with leaks of any type.  Clean up any hydraulic fluid that is spilled 
or has leaked out of the system.  Hydraulic fluid is combustible, and ignition may occur. 

 

With  the  exception  of  instructions  within  this  manual,  never  modify  or  remove  any  of  the 
components within the tray assembly. 

 

Never modify or remove any of the components within the pump or the controls mounted to 
the  pump.    This  includes  all  fittings  and  tubing  that  are  originally  provided  with  the  A.C. 
modular generator system. 

 

Never make any adjustments to the pump other than for flow control.  If it appears the pump 
needs to be adjusted, contact Smart Power Systems

®

 at (231) 832-5525 before proceeding.  

Damage to the generator from improper pump adjustment will void the system’s warranty. 

 

Never attempt any adjustments or repairs to the A.C. modular generator system (other than 
pump flow control) while the vehicle engine is running and the PTO is engaged. 
 
Never operate the system with the hydraulic fluid exceeding 195

F.  Above this temperature, 

hydraulic fluid can rapidly oxidize and deteriorate causing generator performance problems.  
Operating the system while the hydraulic fluid is above 195

F 

will void the system’s warranty.

 

 

Hydraulic fluid is combustible and toxic.  In the event of human contact with hydraulic fluid, 
generously flush body part (eyes, skin, etc.) with running water. Avoid inhalation of any oil 
mist or vapor.  Do not ingest hydraulic fluid.  In case of fire, use foam, dry chemical or carbon 
dioxide to extinguish flame. 

 

Do not exceed the wattage rating of the generator.  The generator may be permanently d 
amaged and the generator and hydraulic components may reach temperatures that could 
cause  severe  burns  upon  human  contact  with  the  components.    Operating  the  generator 
system at wattages 

above the system’s rating will void the system’s warranty. 

 

Disengage  the  system  immediately  if a hydraulic  fluid  leak  is  detected.    Operation  of  the 
A.C. modular generator system with low fluid level will result in permanent damage to the 
hydraulic components in the system and will void the system’s warranty. 

 

Do not tamper with the hydraulic fluid level sensor. 

 

Never attempt to operate the system without hydraulic fluid.  Always maintain a fluid level 
between ½ to ¾ full in the sight plug.   
 
Operating  the  A.C.  modular  generator  system  in  the  presence  of  flammable  vapors  may 
result in an explosion. 

 

Use only hoses that meet or exceed the minimum requirements specified in this manual.  A 
ruptured hose can cause personal injury and/or damage to the generator system. 

 

Do not operate the system under electrical load with air in the hydraulic fluid (the system will 
make a growling sound). Do not allow anything to contact the hydraulic hoses that will cause 

Содержание HR-10


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды