SMART 433-CMU, Инструкция по установке и эксплуатации, Страница: 9 / 12

WIRELESS CALL SYSTEM
CALL REVIEW
VOLUME
LANGUAGE
REPLACE/ADD
RECORD/ADD
RESET
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29 30
WIRELESS CALL SYSTEM
CALL REVIEW
VOLUME
LANGUAGE
REPLACE/ADD
RECORD/ADD
RESET
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29 30
Programming Light
Indicates when the Central Monitor is in programming mode. If the
light is on, the Central Monitor is in programming mode; if the light is
off, it is not in programming mode.
1. Press once to exit programming mode.
2. Press once to silence the Central Monitor
and
erase/clear call memory.
Extend the antenna fully to ensure the best possible reception and range
between the Central Monitor and any programmed Nurse Call buttons or
other components or to optimize the range between the Central Monitor
and pagers.
1. Slide the base off of the Central
Monitor
2. Screw base into wall so
that hooks face out
3. Slide the Central Monitor onto the base (now
screwed onto the wall) so that the hooks from
the Central Monitor connect to the hooks on
the base.
Programming
Light
Reset
Button
Antenna
Screw Holes
Hooks
Hooks
Base
Reset Button
Antenna
Wall Mounting the 433-CMU
To program Nurse Call Buttons or other components into a new or empty system:
1. Refer to previous pages for instructions specific to each component.
To erase all Nurse Call Buttons and other components currently programmed into the Central Monitor System:
1. Press and hold “Record/Add” Button until you hear 2 dings and a melodic tone.
2. Press “Reset” button to exit programming mode.
WARNING:
Pressing the “Record/Add” button will erase/clear all programming from the Central Monitor. After pressing the “Record/Add”
button, all Nurse Call Buttons or other components that were programmed into the Central Monitor will no longer be recognized by the
Central Monitor until they are reprogrammed. Numbers will flash across the Central Monitor to indicate that no Nurse Call Buttons or other
components are currently programmed to work with the Central Monitor.
WARNING:
Pressing the “Reset” button will erase/clear the Central Monitor’s
memory of call history so that the “Call Review” button will be unable to recall any
calls made prior to pressing the “Reset” button.
433-CMU
433-CMU
433-CMU Back
433-CMU Back
433-CMU
Back
9
Record/Add Button
Use this button when you wish to
1. Program Nurse Call Buttons or other components into a new or
empty Central Monitor system
2. Erase all Nurse Call Buttons and other components currently
programmed into the Central Monitor system
Record/Add
WARNING:
If you do not wait for the Central Monitor to make a melodic tone before pressing the next Nurse Call Button or other component,
each component will be programmed to the same number on the Central Monitor. In this situation, the Central Monitor will speak one
number for the component, but show a different number to represent the room. When multiple components are programmed to the same
number on the Central Monitor,
THE NUMBER SPOKEN WILL NOT CORRESPOND WITH THE NUMBER DISPLAYED
. This may be useful when
multiple devices are being used in the same room, but not for any other situation.
WIRELESS CALL SYSTEM
CALL REVIEW
VOLUME
LANGUAGE
REPLACE/ADD
RECORD/ADD
RESET
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29 30