SMAR if303 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 52

SMAR if303 Скачать руководство пользователя страница 10

IF303 - Operation and Maintenance Instruction Manual

1.2

COVER
LOCKING
SCREW

Figure 1.1 - Cover Locking

For convenience there are three ground terminals: one inside the cover and two externals, located
close to the conduit entries.

GROUND
TERMINAL

PROFIBUS PA

AND POWER SUPPLY

TERMINALS

COMUNICATION

TERMINALS

INPUT

TERMINALS (3)

INPUT
GROUND
TERMINAL

Figure 1.2 - Terminal Block

The

IF303

uses the 31.25 kbit/s voltage mode option for the physical signaling. All other devices on

the same bus must use the same signaling.

Various types of Fieldbus devices may be connected on the same bus.

The

IF303

is powered via the bus. The limit for such devices is according to the DP/PA coupler

limitations for one bus (one segment) for non-intrinsically safe requirement.

In hazardous area, the number of devices may be limited by intrinsically safe restrictions, according
to the DP/PA coupler and barriers limitations.

The

IF303

is protected against reverse polarity, and can withstand ±35 VDC without damage, but it

will not operate when in reverse polarity.

NOTE

Please refer to the General Installation, Operation and Maintenance Procedures Manual for more details.

«
...
8
9
10
11
12
...
»

Содержание if303





















































Отзывы:

Нет отзывов