SMA Sunny Boy SB 1100LV страница 17 Скачать руководство пользователя | Manualshive

Страница: 17 / 62

background image

SMA

Technologie AG

Installation requirements

Installation Guide

SB1100LV-11:SE2006

Page 17

AC cable system impedance should not exceed 1 ohm. This is necessary, amongst other
things, for the correct operation of impedance observation. In addition, we recommend
dimensioning the conductor cross-section so that line losses do not exceed 1% at the
nominal power. Line losses depending on the cable length and cross-section are shown
in the graph below. Multi-wire cables with copper forward and return conductors are
used.

The maximum cable lengths for the different cable cross-sections are as follows:

Conductor cross-section

1.5 mm²

2.5 mm²

Max. length

21 m

35 m

Do not use cables where the losses will exceed 1.0%

Cable length

Line l

o

ss

es

«
...
15
16
17
18
19
...
»

Содержание Sunny Boy SB 1100LV































































Отзывы:

Нет отзывов

Похожие инструкции для Sunny Boy SB 1100LV

Бренд: Danfoss Страницы: 7

Бренд: Danfoss Страницы: 16

VLT 2800 Series

Бренд: Danfoss Страницы: 34

VLT AutomationDrive FC 300

Бренд: Danfoss Страницы: 60

VLT 5000 Series

Бренд: Danfoss Страницы: 63

Бренд: G-Lab Страницы: 16

Бренд: Patton electronics Страницы: 12

Бренд: Data Translation Страницы: 62

Бренд: Promax Страницы: 14

Бренд: ORO Страницы: 18

AT-IMC100T/SCMM

Бренд: Allied Telesis Страницы: 20

Бренд: JTS Страницы: 8

Бренд: 3onedata Страницы: 3

Allen-Bradley 842D

Бренд: Rockwell Automation Страницы: 58

Бренд: MAGIRA Страницы: 58

Бренд: M-Audio Страницы: 2

AZZYRRO 3-6-ZSS-HP

Бренд: ZCS Страницы: 65

Rack-mountable 8 x 8 USB 2.0 Interface with MX Core DSP Technology 8R

Бренд: M-Audio Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды