background image

Transformer Installation

Install Transformer (EL-154) on a 2-Gang Electrical Box, 4” x 4” x 2-1/2” 

(102 mm x 102 mm x 64 mm) in a convenient location; refer to the 

illustration at upper right side of this page.

Note: One Sloan EL-154 transformer can operate up 

to ten OPTIMA equipped Flushometers. Run 18-gauge 

wire from transformer to Flushometer(s). Wire supplied 

by others. DO NOT supply power to transformer until 

installation of Flushometer is complete.
Note: A maximum of ten (10) Flushometer units can 

operate from one (1) Sloan EL-154 Transformer, Class 2, 

UL Listed, 50 VA (min.) at 24 VAC, plate mounted.

Sensor Box Location

Failure to properly position the sensor to the plumbing rough-in will result 

in improper installation and impair product performance. All tradesmen 

(plumbers, electricians, tile setters, etc.) involved with the installation of this 

product must coordinate their work to assure proper product installation.

3

Prior to installing the Sloan OPTIMA equipped Flushometer, install the items 

listed below. Refer to Rough-ins on Page 2 and illustration on this page.
•  2-gang electrical box — 4” x 4” x 2-1/2” (102 mm x 102 mm x 64 

mm) for transformer; see paragraph entitled “Transformer Installation” 

(mount in a convenient location)

•  Electrical wiring to the transformer box (120 VAC, 2 amp service 

required for each EL-154, 24 VAC, 50 VA transformer used)

•  Closet/urinal fixture
•  Drain line
•  Water supply line

Important:
•  INSTALL ALL ELECTRICAL WIRING IN ACCORDANCE 

WITH NATIONAL/LOCAL CODES AND REGULATIONS.

•  INSTALL ALL PLUMBING IN ACCORDANCE WITH 

APPLICABLE CODES AND REGULATIONS.

•  WATER SUPPLY LINES MUST BE SIZED TO PROVIDE 

AN ADEQUATE VOLUME OF WATER FOR EACH 

FIXTURE.

•  A 24 VAC STEP-DOWN TRANSFORMER MUST BE 

USED.

•  USE APPROPRIATE PRECAUTIONS WHILE 

CONNECTING TRANSFORMER TO 120 VAC POWER 

SOURCE.

•  FLUSH ALL WATER LINES PRIOR TO MAKING 

CONNECTIONS.

Royal

®

 and Sloan

®

 Flushometers are designed to operate with 15 

to 100 psi (104 to 689 kPa) of water pressure. 

THE MINIMUM 

PRESSURE REQUIRED TO THE VALVE IS DETERMINED 

BY THE TYPE OF FIXTURE SELECTED. 

Consult fixture 

manufacturer for minimum pressure requirements.
Most Low Consumption water closets (1.6 gallon/6.0 liter) require a 

minimum flowing pressure of 25 psi (172 kPa).
Protect the Chrome or Special finish of this Flushometer — 

DO NOT 

USE TOOTHED TOOLS TO INSTALL OR SERVICE THE 

VALVE

. Also, see “Care and Cleaning” section of this manual.

IMPORTANT: EXCEPT FOR CONTROL STOP INLET, DO 

NOT USE PIPE SEALANT OR PLUMBING GREASE ON 

ANY VALVE COMPONENT OR COUPLING!

With the exception of Control Stop Inlet, DO NOT use pipe sealant or plumbing grease 

on any valve component or coupling!

!!! IMPORTANT !!!

Protect the chrome or special finish of Sloan Flushometers —  

DO NOT USE toothed tools to install or service these valves. 

Use a Sloan A-50 Super-Wrench™, Sloan A-109 Plier Wrench or  

smooth jawed spud wrench to secure all couplings. Also see  

“Care and Cleaning” section of this manual.

!!! IMPORTANT !!!

This product contains mechanical and/or electrical components  

that are subject to normal wear. These components should be checked on a regular 

basis and replaced as needed to maintain  

the valve’s performance.

!!! IMPORTANT !!!

If you have questions about how to install your flushometer, 

consult your local Sloan Representative  

or call Sloan Technical Support at:

1-888-SLOAN-14 (1-888-756-2614)

2-GANG ELECTRICAL BOX - 

4” x 4” x 2½” (102 mm x 102 mm x 64 mm)

EL-154 TRANSFORMER †

† MOUNT TRANSFORMER 

WITHIN 50 FEET (15 m) OF 

FLUSHOMETER

PRIOR TO FLUSHOMETER INSTALLATION

TRANSFORMER INSTALLATION AND SENSOR BOX LOCATION

TOOLS REQUIRED FOR INSTALLATION

Never open Control Stop to where the flow from the valve

 exceeds the flow capability of the fixture. In the event of  

a valve failure, the fixture must be able to accommodate a  

continuous flow from the valve.

!!! IMPORTANT !!!

•  Phillips screwdriver
•  Drill – 1/16” and 1” drill bit
•  Wire stripper
•  Sloan A-50 Super-Wrench™, Sloan A-109 Plier Wrench or smooth jawed spud wrench

LAWS AND REGULATIONS PROHIBIT THE USE OF 

HIGHER FLUSHING VOLUMES THAN LISTED ON  

FIXTURE OR FLUSHOMETER.

!!! IMPORTANT !!!

Содержание 150 ES-SM









Отзывы: