15
2728
13
2021
-
SEP 80 & 100 & 120 & 130 & 150
MC_0001
Gear Leg & Motor Bracket Installation
!
Please refer to the graphic for special considerations relating to your model
!
EN
1. Mark the tunnel centreline and the boat’s centreline.
(NB: Install the gear leg and propeller as shown above for the thrust direction to correspond
with the control panel. Position gear leg with the P-mark facing port and the S-mark facing starboard.)
2. Use the gasket or template (recommended) to mark the hole centres and double-check the measurements. The centre hole MUST be placed
using the boat centreline as shown above.
(NB: All holes must be in-line with the tunnels’ centreline for correct installation, clearance between
the propeller and the tunnel is minimal.)
3. Smooth the surface of the tunnel. A rough surface will cause possible failure/movement of the gear leg. The motor bracket must rest steadily on
the tunnel.
4. Drill the main centre hole followed by the two screw-holes.
5. Place the gear leg (without the propeller) with the gasket on inside the tunnel. Place the propeller on the gear leg to ensure it is centred and
rotates freely with the same clearance from each blade to the tunnel wall. Place top motor bracket to measure the drive shaft has come through
the motor bracket at the correct height. Remove the gear leg and propeller for fi nal installation.
6. Apply appropriate sealant to both sides of the gasket and place on the gear leg. Place the gear leg in the tunnel (without the propeller).
7. Install the top motor bracket and gear leg gently together. Use appropriate sealant to ensure that no leakages occur.
(NB: See your sealant data
sheet for the correct application process.)
8. Fasten the gear leg and the motor bracket with the bolts provided. Fasten to torque as shown above.
MG_0055
PORT
STARBOARD
S
P
SE
*P*IP
80
SE
*P*IP
100
FASTEN
18 Nm
(13.28 lb/ft)
SE
*P*IP
120
SE
*P*IP
130
SE
*P*IP
150
SE
*P*IP
170
SE
*P*IP
210
FASTEN
33 Nm
(24 lb/ft)
Tunnel
centre line
Boats
centre line
Bow
Stern
1
STARBOARD
PORT
B
OW
Measurement
Description
mm
inch
ØA
34
1.33
B
28
1.1
ØC
9
0.35
SE
*P*IP
80
SE
*P*IP
100
*P- Propositional
*IP- Ignition Protected
mm
inch
47
1.85
40
1.57
12
0.43
SE
*P*IP
120
SE
*P*IP
130
SE
*P*IP
150
SE
*P*IP
170
SE
*P*IP
210
Gasket
Ensure propeller
turns without
obstruction
5
BOW
BOW
BOW
Apply MS Polymer
sealant or equal to
both sides of the
gasket
Motor bracket
IMPORTANT
Do not apply sealant to
the holes.
6 - 7
2 - 4
8
Tunnel
centre line
Boats
centre line
B
ØC
ØA
B
OW
It is the installers responsibility
When installing Sleipner equipment follow the outlined regulations/ classifi cation rules (electrical/ mechanical) according to
international or special national regulations. Instructions in this guide cannot be guaranteed to comply with global electric/
mechanic regulations/ classifi cation rules.
Follow all health and safety laws in accordance with their local outlined regulations/ classifi cation rules.
Before installation, it is important that the installer reads this guide to ensure necessary acquaintance with the product.
The recommendations made in this manual are guidelines ONLY, and Sleipner Motor AS (Sleipner) strongly recommend that before
installation, advice is obtained from a naval architect familiar with the particular vessel and regulations/ classifi cations.
This manual is intended to support educated/ experienced staff and is therefore not suffi cient in all details for professional
installation.
(NB: These instructions are only general instruction. If you are not skilled to do this work, please contact professional
installers for assistance.)
All electrical work must be done by a licensed professional.
Faulty installation of Sleipner products will render all warranty given by Sleipner Motor AS void.
MC_0038
IMPORTANT
If installing S-link products DO NOT connect any other control equipment to the S-link controlled products except Sleipner original S-link
products or via a Sleipner supplied interface product made for interfacing with other controls. Any attempt to directly control or at all connect
into the S-link control system without the designated and approved interface will render all warranties and responsibilities for the complete
line of Sleipner products connected void and null. If you are interfacing by agreement with Sleipner and through a designated SLeipner
supplied interface, you are still required to also install at least one original Sleipner control panel to enable effi cient troubleshooting if
necessary.
MC_0265