manualshive.com logo in svg

SLEIPNER MOTOR AS SRH-240/250 TC, Руководство по установке

Поделиться
Скачать
SLEIPNER MOTOR AS SRH-240/250 TC Скачать руководство пользователя страница 25

 25

2933

6

2021

-

SH 240 & SH 320

MC_0033

Pre-delivery Checklist

EN

�.......... The bolts holding the gear house and motor bracket together are tightened correctly.

�.......... The bolts holding the motor to its bracket are tightened correctly.

�.......... All electrical connections are clean, dry and tight, and the correct cable, fuse and main  

 

   switch size.

�.......... Check that there is no electrical connection between the electro motor body and positive     

         terminal on the motor, and between the electro motor body and the negative (A1) terminal  

 

   on the motor with an ohm meter.

�.......... Anti-fouling has been applied to the gear house and propeller but NOT anodes, sealing/  

 

   rubber fi ttings or propeller shafts.

�.......... Propeller is fastened correctly to the shaft.

�.......... Propeller turns freely in tunnel.

�.......... The anode and/ or holding screw is tightened well with thread glue.

�.......... Check the boat for potential water leakage around installation areas.

�.......... Correct drive direction as per control panel.

�.......... User Manual is supplied to the owner.

The thruster has been installed as per the instructions in this manual and all points in checklist above have been controlled.

Signed: .........................................................................................

Date: .............................................................................................

Thruster type: ................................................................................................................................................................................................

Serial number:...............................................................................................................................................................................................

Date of delivery:.............................................................................................................................................................................................

Correct drive direction as per control panel: ..................................................................................................................................................

The compartment for the thruster has been isolated from general bilge water and has no obvious or suspected risks for  flooding: 

......................................................................................................................................................................................................................

......................................................................................................................................................................................................................

......................................................................................................................................................................................................................

Other comments by installer: ........................................................................................................................................................................

.......................................................................................................................................................................................................................

.......................................................................................................................................................................................................................

Control Panel Installation 

EN

Find a suitable location for the control panel where it does not obstruct or is obstructed by other devices. Install the control panel on a flat surface 

where it is easy to use. 

1.  Use the supplied cut-out template to mark the area to remove on your control dash. 

2.  Cut out the area per template for the control panel. (

NB: If the front surface around your cut out is jagged or chipped, use a sealant

to assist the gasket.)

3.  Place the gasket to the back face of the panel 

4.  Plug cables into the connectors at the rear of the control panel. 

5.  Insert the control panel in place and fasten screws.

6.  Insert the control panels covering caps.

MC_0042

!

 Please refer to the graphic for special considerations relating to your model 

!

MG_0063

GASKET   

4x SCREWS 

58 mm

67 mm

125 mm

116 mm

132.7 mm

75.7 mm

Ø 4.5 mm

Ø 4.5 mm

Ø 4.5 mm

Ø 4.5 mm

(S-link)

External alarm buzzer

12V / 24V DC - max 0,5A

External alarm / buzzer connection

Supply

+ 12V / 24V DC 

-

+

Ø 4.5 mm

Rear

side

of pa

nel

Internal

fuse / relay

Содержание SRH-240/250 TC





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды