background image

SkyTrac Systems Ltd. 

 

Document Rev. 01.020 

DOC0334 

Page 15 of 49 

Restricted Proprietary and Confidential Information 

Table 10

— TSO Combination Antenna Specifications (PN: STS-ISAT-ANT) 

 

Description 

Active L1 GPS/Passive Iridium Antenna, low profile, moulded radome  

Height 

0.721 in.  

Length 

5.026 in.  

Width 

2.0 in.  

Weight 

8.0 oz  

Voltage 

2.8 to 28.0 VDC @ 50 mA max 

Gain (GPS antenna):   

32 dB min 

 

Table 11

— Li-ion Battery Specifications 

 

 

STS0061 

STS0044 

Description 

2 cell Li-ion battery pack with built-in 
protection circuitry 

2 cell Li-ion battery pack with built-in 
protection circuitry 

Capacity 

7.2V nominal 2700 mAh 

7.2V nominal 2250 mAh 

Operation 

-10°C to +60°C¹ 

-20°C to +60°C¹ 

Charging:   

0°C to +45°C² 

0°C to +45°C² 

Storage:         

-20°C to +60°C

3

 

-20°C to +60°C

3

 

Dimensions: 

5.2 in x 0.90 in x 0.75 in 

5.2 in x 0.90 in x 0.75 in 

Weight 

0.22 lb 

0.215 lb 

Connector 

MOLEX 43025-0400 

MOLEX 43025-0400 

Over Discharge Protection:     2.32 Volts/cell 

2.2 Volts/cell 

Over Charge Protection:          4.325 Volts/cell 

4.375 Volts/cell 

Over Current Protection: 

6.5A max 

7A max 

Over Temperature 
Protection: 

Built-in thermal protection circuit 
disables cell in case of overheating 

Built-in thermal protection circuit 
disables cell in case of overheating 

 
 

Note  1

 

–  Operating  the  battery  pack  below  -10

  C  results  in  reduced  performance.  Operating  the 

battery pack above +60

C may cause reduced life and capacity of the battery. 

 

Note  2

-  The  ISAT-200  has  a  built-in  protection  circuit  to  prevent  charging  outside  of  the  battery 

charging operational range. 

 

Note 3

 - Store batteries at room temperature at 30-50% of capacity for maximum battery life.  

 
Please refer to Appendix B: Battery Precautions for additional information on operating conditions. 

 

The document reference is online, please check the correspondence between the online documentation and the printed version.

Содержание 101-200-01



















































Отзывы: