background image

___________________________________________________________________________________________________________ 

REV 7/10/15 

Page 5 of 5

 

Skytech TM/R 2-A 

BATTERY LIFE 

 
Life expectancy of the alkaline batteries in the transmitter should be at least 12 months.  Check and replace all batteries annually.  
When the transmitter no longer operates the remote receiver from a distance it did previously (i.e., the transmitter’s range has 
decreased) or the remote receiver does not function at all, the batteries should be checked.  It is important that the remote receiver 
batteries are fully charged and provides continuous output voltage of a least 5.3 volts.  The length of the wire between the remote 
receiver and gas valve directly affects the operating performance of the remote system.  The longer the wire, the more battery power is 
required to deliver signals between the remote receiver and the gas valve.  Recommended length is no longer than 20 feet. The Wall 
Transmitter should operate with as little as 2.4 volts of battery power, measuring at each of the 3-volt button cell batteries.  
 

 
TROUBLE SHOOTING 

 
If you encounter problems with your fireplace system, the problem may be with the fireplace itself or it could be with the SKYTECH 
remote.  Review the fireplace manufacturer’s operation manual to make sure all connections are properly made.  Then check the 
operation of the SKYTECH remote in the following manner: 

 

Make sure the batteries are correctly installed in the RECEIVER.  One reversed battery will keep receiver from operating properly. 

 

Check battery in Wall Transmitter to make sure they are good and installed correctly.  

 

Be sure RECEIVER and Transmitter are within 20 to 25-foot operating range. 

 

Keep RECEIVER from temperatures exceeding 130

0

 F.  Battery life shortened when ambient temperatures are above 130

0

 F. 

 

If RECEIVER is installed in tightly enclosed metal surround, the operating distance will be shortened.  

 

 

 

SPECIFICATIONS 
 

BATTERIES:  Transmitter (2) 3V Button Cell Batteries (CR-2032)                       
 

         Remote Receiver 6V –4ea. AA 1.5 Alkaline                       FCC ID No.’s: transmitter –K9LTMR2A; receiver – K9L3301RX  

Operating Frequency:  303.875MHZ                               Canadian ISC ID No.’s:  transmitter –2439A-TMR2A; receiver – 2439A-3301RX 
 

 
 
 
 
 
 

 
 

FOR TECHNICAL SERVICE, CALL: 

 

U.S. INQUIRIES   

 

CANADIAN INQUIRIES 

 

 

 

 

 

(855) 498-8324 or (260) 459-1703   

       (877) 472-3923 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

For Sales: (888) 672-8929 

Website:  skytechsystem.com 

 

MANUFACTURED EXCLUSIVELY FOR SKYTECH II, INC 

 
 
 
 
 

FCC REQUIREMENTS 

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED 
MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE 
EQUIPMENT. 

 

www.FireplaceRemoteControls.com

1.888.977.6849

Содержание TM/R-2






Отзывы: