background image

RC-

AA

-PROG

R

 Remote Control Thermostat 

INSTRUCTION MANUAL 

IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO 

NOT ATTEMPT TO INSTALL OR OPERATE

This remote control system was developed to provide a safe, reliable, and user-friendly remote control system for gas 
heating appliances or other compatible appliances. The system can be operated manually from the transmitter.

 

The receiver wires must be connected to the thermostat leads on your appliance.  
Refer to your appliance manual for proper wiring instructions. 

The transmitter operates on 4 AAA 1.5V batteries 
that are included. Install the batteries 
supplied with the unit into the battery 
compartment. It is recommended that 
ALKALINE batteries always be used for this 
product. 

Be sure the batteries are 

installed with the (+) and (-) ends facing the 
correct direction. 

When you start up the remote, if a low battery signal appears or if the LCD screen 
does not illuminate when you touch it, check battery position and if the batteries are 
fully charged

.

 

TRANSMITTER BUTTONS 

1. [MODE]

 - Switches the appliance on/thermo/off.

2. [PROG]

 - Turns on and off the program function.

3. [SET]

 - Used in different functions to confirm settings.

1. BATTERY ICON

 - Battery power is low.  See SETUP STEP 2.

2. ROOM

 - Indicates CURRENT room temperature.

3. SET 

- Indicates desired SET room temperature for THERMO operation.  See

PROGRAM STEP 1.

4. FAHRENHEIT/CELSIUS

 - Indicates Fahrenheit/Celsius.  See SETUP STEP 5.

5. FLAME

- Indicates appliance is ON.

6. MODE

 – Indicates operation mode of system.  See SETUP STEP 6.

7. UP

 and 

DOWN

 touchscreen icons – These are used to adjust the Time, Set

temperature, and Program functions.

8. TIME

 and 

PROGRAM TIME

 – Indicates current time or program time setting

when editing program settings.

9. LOCK

 - Child lock out.  See SETUP STEP 3.

10. PROGRAM ON/OFF

 – Indicates when Program 1 (P1) is on or off, and

indicates when Program 2 (P2) is on or off.  See PROGRAM STEP 4.

11. DAY of WEEK

 - Indicates current day of week, or program segment when

editing program settings.

Содержание RC-AA-PROGR









Отзывы: