Skymsen SKG, Инструкция по эксплуатации

Страница: 15 / 20

12
5.2.3 – Thickness Adjustment
The Thickness Guide was developed to help user on cutting and to improve safety. Its
main function is to provide cuts with the same thickness.
To adjust the Thickness Guide, follow the procedures below:
· Rotate the handle #.12 (Pic.01) anti-clockwise to move the Thickness Guide.
· Using the spherical handle #17 (Pic.01), move the Thickness Guide horizontally upon
the Stationary Table #.14 (Pic.01), increasing or decreasing the distance between the
Thickness Guide and the Blade, according to your necessity.
· Rotate the spherical handle # 17 (Pic.01) clockwise to lock the Thickness Guide on the
desired position.
5.2.4 Blade Guide Adjustment
The blade guide # 06 (Pic.01) adjustment shall be made accordingly to the height of the
product that will be cut. Its main function is to keep the blade perpendicular to the stationary table
and inflexible.
To adjust the Blade Guide # 06 (Pic.01), proceed according to description below,
keeping the machine disconnected from the power line:
· Turn the handle # 05 (Pic.01) anti-clockwise to allow vertical movement.
· Adjust it as close as possible to the product that will be cut, however being careful not to
avoid any free movement.
· Turn the handle # 05 (Pic.01) clockwise to fix the Blade Guide in the wanted position.
5.2.5 – Upper Bearing Adjustment
The adjustment of the Upper Bearing is made in order to centralize the blade on the
wheel, to prevent it from skipping.
To adjust the Upper Bearing, proceed according to description below, keeping the
machine disconnected from the power line:
· Loosen the Blade #.07 (Pic.01) using the graduator, accordingly to item 3.2.3
· Take out the upper rear lid, removing the Screws using a 10 mm spanner.
· Loosen the three nuts #.01 (Pic.03) with a 10 mm spanner.
· Using a screw driver, rotate the screw #. 02 ( Pic. 03 ) ¼ of a turn anti-clockwise, if the
blade is dislocated to the front. If the blade is dislocated to the back, rotate the Screw ¼
of a turn clockwise.
· Tighten the three nuts #.01 (Pic.03), previously loosen., with a 10 mm spanner
· Adjust the blade according to description on 5.2.2
· Manually rotate the Wheel and check if the Blade is centered on it. Proceed like this until
the blade is centered.
Picture - 02
02 01
Picture - 03
02
03
01
23
5. Analice y Solución de Problemas
5.1 Problemas, Causas y Soluciones
* La vida de servicio - 2 años para la jornada de trabajo normal
Las Sierras Modelo SKG , fueran diseñadas para que necesiten un mínimo de manutención .
Sin embargo pueden ocurrir algunas irregularidades en su funcionamiento , debido al desgaste
natural causado por su uso .
Caso haya algún problema con su maquina , verifique la Tabla – 02 abajo , donde están
indicadas algunas soluciones recomendadas .
Tabla - 02
* La maquina no prende * L a m a q u i n a e s t a
desconectada de la red
eléctrica.
* Falta de Energía Eléctrica
* Averigüe si hay energía
eléctrica
* Ponga la flecha del cable de
la toma eléctrica.
* Olor a quemado o humo * Problema con el motor o
otros circuitos eléctricos * Llame la asistencia técnica.
* Correa patinando
* Capacitor de partida del
motor con defecto.
* Ajuste la tensión de la correa
de acuerdo con el ítem 5.2
* Llame la asistencia técnica.
* La maquina liga, pero
cuando el producto entra en
contacto con la hoja, la
misma para o gira en baja
Rotación
Causa Problema Solucón